FreeBSD 13.0-RELEASE Hardware Notes
Table of Contents
Introduction
This document contains the hardware compatibility notes for FreeBSD 13.0-RELEASE. It lists the hardware platforms supported by FreeBSD, as well as the various types of hardware devices (storage controllers, network interfaces, and so on), along with known working instances of these devices.
Supported Processors and System Boards
This section provides some architecture-specific information about the specific processors and systems that are supported by each architecture.
amd64
FreeBSD/amd64 supports the 64-bit x86 architecture and runs on a wide variety of machines. It is a Tier-1 platform (fully supported architecture), which is expected to be Production Quality with respects to all aspects of the FreeBSD operating system, including installation and development environments. Due to the wide range of hardware available for this architecture, it is impossible to exhaustively list all combinations of equipment supported by FreeBSD. Nevertheless, some general guidelines are presented here.
All 64-bit x86 processors are supported including AMD64 CPUs from AMD and Intel® 64 CPUs from Intel including Xeon and Core processors. FreeBSD/amd64 supports multi-core and SMT (Symmetric MultiThreading, also known as HyperThreading on Intel® CPUs) processors.
Note that there are various names for this architecture including x86-64, AMD64, Intel EM64T, and IA-32e.
FreeBSD/amd64 requires Advanced Configuration and Power Management (ACPI) support. ACPI is supported by the ACPI Component Architecture reference implementation from Intel®, as described in the acpi(4) manual page.
FreeBSD/amd64 can boot on systems using both UEFI and legacy BIOS.
FreeBSD will generally run on amd64-based laptops, desktops, and servers. Support for certain hardware features such as sound, graphics, wireless, and power management may vary depending on the specific hardware devices in use.
i386
FreeBSD/i386 supports the 32-bit x86 architecture and runs on a wide variety of "IBM PC compatible" machines. As with FreeBSD/amd64, it is impossible to exhaustively list all combinations of equipment supported by FreeBSD, but some general guidelines are presented here.
All 32-bit x86 compatible processors with a floating point unit and support for the CMPXCHG instruction (introduced in the 80486) are supported. This includes the Pentium® families of processors from Intel as well as x86-compatible processors from AMD, Cyrix, NexGen, and VIA.
There are a wide variety of motherboards available for this architecture. Motherboards using PCI expansion buses are well-supported. There is limited support for AGP devices, and ISA support is primarily focused on legacy devices emulated in LPC bridges on modern PCI systems.
Symmetric multi-processor (SMP) systems are generally supported including multi-core and SMT.
FreeBSD will take advantage of Physical Address Extensions (PAE)
support on CPUs that support this feature. The default kernel
supports memory up to 24 gigabytes, but device drivers will use
bounce buffers to access I/O buffers in memory above 4 gigabytes. A
custom kernel with the PAE
feature enabled will avoid
the use of bounce buffers, but disables a few incompatible device
drivers. This feature places constraints on other features of
FreeBSD which may be used; consult the
pae(4) manual page for more details.
FreeBSD will generally run on i386-based laptops, desktops, and servers. Support for certain hardware features such as sound, graphics, wireless, and power management may vary depending on the specific hardware devices in use.
FreeBSD/i386 supports ACPI which is used by modern machines, but is also able to boot on older systems without ACPI support.
FreeBSD/i386 only supports booting from systems using legacy BIOS. It cannot be booted from UEFI.
powerpc
All Apple PowerPC machines with built-in USB are supported, as well as limited selection of non-Apple machines, including KVM on POWER7
SMP is supported on all systems with more than 1 processor.
Supported Devices
This section describes the devices currently known to be supported by FreeBSD. Other configurations may also work, but simply have not been tested yet. Feedback, updates, and corrections to this list are encouraged.
Where possible, the drivers applicable to each device or class of devices is listed. If the driver in question has a manual page in the FreeBSD base distribution (most should), it is referenced here. Information on specific models of supported devices, controllers, etc. can be found in the manual pages.
Note:
The device lists in this document are being generated automatically
from FreeBSD manual pages. This means that some devices, which are
supported by multiple drivers, may appear multiple times.
Disk Controllers
[amd64, i386] IDE/ATA controllers (ata(4) driver)
Controllers supported by the aac(4) driver include:
-
Adaptec AAC-364
-
Adaptec RAID 2045
-
Adaptec RAID 2405
-
Adaptec RAID 2445
-
Adaptec RAID 2805
-
Adaptec RAID 3085
-
Adaptec RAID 31205
-
Adaptec RAID 31605
-
Adaptec RAID 5085
-
Adaptec RAID 51205
-
Adaptec RAID 51245
-
Adaptec RAID 51605
-
Adaptec RAID 51645
-
Adaptec RAID 52445
-
Adaptec RAID 5405
-
Adaptec RAID 5445
-
Adaptec RAID 5805
-
Adaptec SAS RAID 3405
-
Adaptec SAS RAID 3805
-
Adaptec SAS RAID 4000SAS
-
Adaptec SAS RAID 4005SAS
-
Adaptec SAS RAID 4800SAS
-
Adaptec SAS RAID 4805SAS
-
Adaptec SATA RAID 2020SA ZCR
-
Adaptec SATA RAID 2025SA ZCR
-
Adaptec SATA RAID 2026ZCR
-
Adaptec SATA RAID 2410SA
-
Adaptec SATA RAID 2420SA
-
Adaptec SATA RAID 2610SA
-
Adaptec SATA RAID 2620SA
-
Adaptec SATA RAID 2810SA
-
Adaptec SATA RAID 2820SA
-
Adaptec SATA RAID 21610SA
-
Adaptec SCSI RAID 2020ZCR
-
Adaptec SCSI RAID 2025ZCR
-
Adaptec SCSI RAID 2120S
-
Adaptec SCSI RAID 2130S
-
Adaptec SCSI RAID 2130SLP
-
Adaptec SCSI RAID 2230SLP
-
Adaptec SCSI RAID 2200S
-
Adaptec SCSI RAID 2240S
-
Adaptec SCSI RAID 3230S
-
Adaptec SCSI RAID 3240S
-
Adaptec SCSI RAID 5400S
-
Dell CERC SATA RAID 2
-
Dell PERC 2/Si
-
Dell PERC 2/QC
-
Dell PERC 3/Si
-
Dell PERC 3/Di
-
Dell PERC 320/DC
-
HP ML110 G2 (Adaptec SATA RAID 2610SA)
-
HP NetRAID 4M
-
IBM ServeRAID 8i
-
IBM ServeRAID 8k
-
IBM ServeRAID 8s
-
ICP RAID ICP5045BL
-
ICP RAID ICP5085BL
-
ICP RAID ICP5085SL
-
ICP RAID ICP5125BR
-
ICP RAID ICP5125SL
-
ICP RAID ICP5165BR
-
ICP RAID ICP5165SL
-
ICP RAID ICP5445SL
-
ICP RAID ICP5805BL
-
ICP RAID ICP5805SL
-
ICP ICP5085BR SAS RAID
-
ICP ICP9085LI SAS RAID
-
ICP ICP9047MA SATA RAID
-
ICP ICP9067MA SATA RAID
-
ICP ICP9087MA SATA RAID
-
ICP ICP9014RO SCSI RAID
-
ICP ICP9024RO SCSI RAID
-
Legend S220
-
Legend S230
-
Sun STK RAID REM
-
Sun STK RAID EM
-
SG-XPCIESAS-R-IN
-
SG-XPCIESAS-R-EX
-
AOC-USAS-S4i
-
AOC-USAS-S8i
-
AOC-USAS-S4iR
-
AOC-USAS-S8iR
-
AOC-USAS-S8i-LP
-
AOC-USAS-S8iR-LP
The adv(4) driver supports the following SCSI controllers:
-
AdvanSys ABP510/5150
-
AdvanSys ABP5140
-
AdvanSys ABP5142
-
AdvanSys ABP902/3902
-
AdvanSys ABP3905
-
AdvanSys ABP915
-
AdvanSys ABP920
-
AdvanSys ABP3922
-
AdvanSys ABP3925
-
AdvanSys ABP930, ABP930U, ABP930UA
-
AdvanSys ABP960, ABP960U
-
AdvanSys ABP542
-
AdvanSys ABP842
-
AdvanSys ABP940
-
AdvanSys ABP940UA/3940UA
-
AdvanSys ABP940U
-
AdvanSys ABP3960UA
-
AdvanSys ABP970, ABP970U
-
AdvanSys ABP852
-
AdvanSys ABP950
-
AdvanSys ABP980, ABP980U
-
AdvanSys ABP980UA/3980UA
The adw(4) driver supports SCSI controllers including:
-
AdvanSys ABP940UW/ABP3940UW
-
AdvanSys ABP950UW
-
AdvanSys ABP970UW
-
AdvanSys ABP3940U2W
-
AdvanSys ABP3950U2W
The aha(4) driver supports the following SCSI host adapters:
-
Adaptec AHA-154xB
-
Adaptec AHA-154xC
-
Adaptec AHA-154xCF
-
Adaptec AHA-154xCP
-
DTC 3290 SCSI controller in 1542 emulation mode
-
Tekram SCSI controllers in 154x emulation mode
The ahc(4) driver supports the following SCSI host adapter chips and SCSI controller cards:
-
Adaptec AIC7770 host adapter chip
-
Adaptec AIC7850 host adapter chip
-
Adaptec AIC7860 host adapter chip
-
Adaptec AIC7870 host adapter chip
-
Adaptec AIC7880 host adapter chip
-
Adaptec AIC7890 host adapter chip
-
Adaptec AIC7891 host adapter chip
-
Adaptec AIC7892 host adapter chip
-
Adaptec AIC7895 host adapter chip
-
Adaptec AIC7896 host adapter chip
-
Adaptec AIC7897 host adapter chip
-
Adaptec AIC7899 host adapter chip
-
Adaptec 274X(W)
-
Adaptec 274X(T)
-
Adaptec 2910
-
Adaptec 2915
-
Adaptec 2920C
-
Adaptec 2930C
-
Adaptec 2930U2
-
Adaptec 2940
-
Adaptec 2940J
-
Adaptec 2940N
-
Adaptec 2940U
-
Adaptec 2940AU
-
Adaptec 2940UW
-
Adaptec 2940UW Dual
-
Adaptec 2940UW Pro
-
Adaptec 2940U2W
-
Adaptec 2940U2B
-
Adaptec 2950U2W
-
Adaptec 2950U2B
-
Adaptec 19160B
-
Adaptec 29160B
-
Adaptec 29160N
-
Adaptec 3940
-
Adaptec 3940U
-
Adaptec 3940AU
-
Adaptec 3940UW
-
Adaptec 3940AUW
-
Adaptec 3940U2W
-
Adaptec 3950U2
-
Adaptec 3960
-
Adaptec 39160
-
Adaptec 3985
-
Adaptec 4944UW
-
Many motherboards with on-board SCSI support
The ahci(4) driver supports AHCI compatible controllers having PCI class 1 (mass storage), subclass 6 (SATA) and programming interface 1 (AHCI).
Also, in cooperation with atamarvell and atajmicron drivers of ata(4) , it supports AHCI part of legacy-PATA + AHCI-SATA combined controllers, such as JMicron JMB36x and Marvell 88SE61xx.
The ahd(4) driver supports the following:
-
Adaptec AIC7901 host adapter chip
-
Adaptec AIC7901A host adapter chip
-
Adaptec AIC7902 host adapter chip
-
Adaptec 29320 host adapter
-
Adaptec 39320 host adapter
-
Many motherboards with on-board SCSI support
The adapters supported by the aic(4) driver include:
-
Adaptec AHA-1505 (ISA)
-
Adaptec AHA-1510A, AHA-1510B (ISA)
-
Adaptec AHA-1520A, AHA-1520B (ISA)
-
Adaptec AHA-1522A, AHA-1522B (ISA)
-
Adaptec AHA-1535 (ISA)
-
Creative Labs SoundBlaster SCSI host adapter (ISA)
-
Adaptec AHA-1460, AHA-1460B, AHA-1460C, AHA-1460D (PC Card)
Controllers supported by the amr(4) driver include:
-
MegaRAID SATA 150-4
-
MegaRAID SATA 150-6
-
MegaRAID SATA 300-4X
-
MegaRAID SATA 300-8X
-
MegaRAID SCSI 320-1E
-
MegaRAID SCSI 320-2E
-
MegaRAID SCSI 320-4E
-
MegaRAID SCSI 320-0X
-
MegaRAID SCSI 320-2X
-
MegaRAID SCSI 320-4X
-
MegaRAID SCSI 320-0
-
MegaRAID SCSI 320-1
-
MegaRAID SCSI 320-2
-
MegaRAID SCSI 320-4
-
MegaRAID Series 418
-
MegaRAID i4 133 RAID
-
MegaRAID Elite 1500 (Series 467)
-
MegaRAID Elite 1600 (Series 493)
-
MegaRAID Elite 1650 (Series 4xx)
-
MegaRAID Enterprise 1200 (Series 428)
-
MegaRAID Enterprise 1300 (Series 434)
-
MegaRAID Enterprise 1400 (Series 438)
-
MegaRAID Enterprise 1500 (Series 467)
-
MegaRAID Enterprise 1600 (Series 471)
-
MegaRAID Express 100 (Series 466WS)
-
MegaRAID Express 200 (Series 466)
-
MegaRAID Express 300 (Series 490)
-
MegaRAID Express 500 (Series 475)
-
Dell PERC
-
Dell PERC 2/SC
-
Dell PERC 2/DC
-
Dell PERC 3/DCL
-
Dell PERC 3/QC
-
Dell PERC 4/DC
-
Dell PERC 4/IM
-
Dell PERC 4/SC
-
Dell PERC 4/Di
-
Dell PERC 4e/DC
-
Dell PERC 4e/Di
-
Dell PERC 4e/Si
-
Dell PERC 4ei
-
HP NetRAID-1/Si
-
HP NetRAID-3/Si (D4943A)
-
HP Embedded NetRAID
-
Intel RAID Controller SRCS16
-
Intel RAID Controller SRCU42X
The arcmsr(4) driver supports the following cards:
-
ARC-1110
-
ARC-1120
-
ARC-1130
-
ARC-1160
-
ARC-1170
-
ARC-1110ML
-
ARC-1120ML
-
ARC-1130ML
-
ARC-1160ML
-
ARC-1200
-
ARC-1201
-
ARC-1203
-
ARC-1210
-
ARC-1212
-
ARC-1213
-
ARC-1214
-
ARC-1216
-
ARC-1220
-
ARC-1222
-
ARC-1223
-
ARC-1224
-
ARC-1226
-
ARC-1230
-
ARC-1231
-
ARC-1260
-
ARC-1261
-
ARC-1270
-
ARC-1280
-
ARC-1210ML
-
ARC-1220ML
-
ARC-1231ML
-
ARC-1261ML
-
ARC-1280ML
-
ARC-1380
-
ARC-1381
-
ARC-1680
-
ARC-1681
-
ARC-1880
-
ARC-1882
-
ARC-1883
-
ARC-1884
The bt(4) driver supports the following BusLogic MultiMaster “W”, “C”, “S”, and “A” series and compatible SCSI host adapters:
-
BusLogic BT-445C
-
BusLogic BT-445S
-
BusLogic BT-540CF
-
BusLogic BT-542B
-
BusLogic BT-542B
-
BusLogic BT-542D
-
BusLogic BT-545C
-
BusLogic BT-545S
-
BusLogic/BusTek BT-640
-
BusLogic BT-946C
-
BusLogic BT-948
-
BusLogic BT-956C
-
BusLogic BT-956CD
-
BusLogic BT-958
-
BusLogic BT-958D
-
Storage Dimensions SDC3211B / SDC3211F
Controllers supported by the ciss(4) driver include:
-
Compaq Smart Array 5300 (simple mode only)
-
Compaq Smart Array 532
-
Compaq Smart Array 5i
-
HP Smart Array 5312
-
HP Smart Array 6i
-
HP Smart Array 641
-
HP Smart Array 642
-
HP Smart Array 6400
-
HP Smart Array 6400 EM
-
HP Smart Array E200
-
HP Smart Array E200i
-
HP Smart Array P212
-
HP Smart Array P220i
-
HP Smart Array P222
-
HP Smart Array P230i
-
HP Smart Array P400
-
HP Smart Array P400i
-
HP Smart Array P410
-
HP Smart Array P410i
-
HP Smart Array P411
-
HP Smart Array P420
-
HP Smart Array P420i
-
HP Smart Array P421
-
HP Smart Array P430
-
HP Smart Array P430i
-
HP Smart Array P431
-
HP Smart Array P530
-
HP Smart Array P531
-
HP Smart Array P600
-
HP Smart Array P721m
-
HP Smart Array P731m
-
HP Smart Array P800
-
HP Smart Array P812
-
HP Smart Array P830
-
HP Smart Array P830i
-
HP Modular Smart Array 20 (MSA20)
-
HP Modular Smart Array 500 (MSA500)
The dpt(4) driver provides support for the following RAID adapters:
-
DPT Smart Cache Plus
-
Smart Cache II (PM2?2?, PM2024/PM2124 [PCI]) (Gen2)
-
Smart RAID II (PM3?2?, PM3021, PM3222)
-
Smart Cache III (PM2?3?)
-
Smart RAID III (PM3?3?, PM3334UW [PCI]) (Gen3)
-
Smart Cache IV (PM2?4?, PM2044/PM2144 [PCI]) (Gen4)
-
Smart RAID IV
Note:
[amd64, i386] Booting from these controllers is supported. EISA
adapters are not supported.
Controllers supported by the esp(4) driver include:
-
Sun ESP family
-
Sun FAS family
-
Tekram DC390
-
Tekram DC390T
The hpt27xx(4) driver supports the following SAS controllers:
-
HighPoint’s RocketRAID 271x series
-
HighPoint’s RocketRAID 272x series
-
HighPoint’s RocketRAID 274x series
-
HighPoint’s RocketRAID 276x series
-
HighPoint’s RocketRAID 278x series
The hptiop(4) driver supports the following SAS and SATA RAID controllers:
-
HighPoint RocketRAID 4522
-
HighPoint RocketRAID 4521
-
HighPoint RocketRAID 4520
-
HighPoint RocketRAID 4322
-
HighPoint RocketRAID 4321
-
HighPoint RocketRAID 4320
-
HighPoint RocketRAID 4311
-
HighPoint RocketRAID 4310
-
HighPoint RocketRAID 3640
-
HighPoint RocketRAID 3622
-
HighPoint RocketRAID 3620
The hptiop(4) driver also supports the following SAS and SATA RAID controllers that are already End-of-Life:
-
HighPoint RocketRAID 4211
-
HighPoint RocketRAID 4210
-
HighPoint RocketRAID 3560
-
HighPoint RocketRAID 3540
-
HighPoint RocketRAID 3530
-
HighPoint RocketRAID 3522
-
HighPoint RocketRAID 3521
-
HighPoint RocketRAID 3520
-
HighPoint RocketRAID 3511
-
HighPoint RocketRAID 3510
-
HighPoint RocketRAID 3410
-
HighPoint RocketRAID 3320
-
HighPoint RocketRAID 3220
-
HighPoint RocketRAID 3122
-
HighPoint RocketRAID 3120
-
HighPoint RocketRAID 3020
The hptmv(4) driver supports the following ATA RAID controllers:
-
HighPoint’s RocketRAID 182x series
The hptrr(4) driver supports the following RAID controllers:
-
RocketRAID 172x series
-
RocketRAID 174x series
-
RocketRAID 2210
-
RocketRAID 222x series
-
RocketRAID 2240
-
RocketRAID 230x series
-
RocketRAID 231x series
-
RocketRAID 232x series
-
RocketRAID 2340
-
RocketRAID 2522
The following controllers are supported by the ida(4) driver:
-
Compaq SMART Array 221
-
Compaq Integrated SMART Array Controller
-
Compaq SMART Array 4200
-
Compaq SMART Array 4250ES
-
Compaq SMART 3200 Controller
-
Compaq SMART 3100ES Controller
-
Compaq SMART-2/DH Controller
-
Compaq SMART-2/SL Controller
-
Compaq SMART-2/P Controller
Controllers supported by the iir(4) driver include:
-
Intel RAID Controller SRCMR
-
Intel Server RAID Controller U3-l (SRCU31a)
-
Intel Server RAID Controller U3-1L (SRCU31La)
-
Intel Server RAID Controller U3-2 (SRCU32)
-
All past and future releases of Intel and ICP RAID Controllers.
-
Intel RAID Controller SRCU21 (discontinued)
-
Intel RAID Controller SRCU31 (older revision, not compatible)
-
Intel RAID Controller SRCU31L (older revision, not compatible)
The SRCU31 and SRCU31L can be updated via a firmware update available from Intel.
Controllers supported by the ips(4) driver include:
-
IBM ServeRAID 3H
-
ServeRAID 4L/4M/4H
-
ServeRAID Series 5
-
ServeRAID 6i/6M
-
ServeRAID 7t/7k/7M
The isci(4) driver provides support for Intel C600 SAS controllers.
Cards supported by the isp(4) driver include:
-
Qlogic 1000
-
Qlogic 1020
-
Qlogic 1040
-
Qlogic 1080
-
Qlogic 10160
-
Qlogic 1240
-
Qlogic 1280
-
Qlogic 12160
-
Qlogic 210X
-
Qlogic 220X
-
Qlogic 2300
-
Qlogic 2312
-
Qlogic 234X
-
Qlogic 2322
-
Qlogic 200
-
Qlogic 2422
-
Qlogic 246x (aka 2432)
-
Qlogic 256x (aka 2532)
-
Qlogic 267x/836x (aka 2031/8031)
-
Qlogic 2690/2692/2694 (aka 2684/2692)
-
Qlogic 2740/2742/2764 (aka 2722/2714)
The mfi(4) driver supports the following hardware:
-
LSI MegaRAID SAS 1078
-
LSI MegaRAID SAS 8408E
-
LSI MegaRAID SAS 8480E
-
LSI MegaRAID SAS 9240
-
LSI MegaRAID SAS 9260
-
Dell PERC5
-
Dell PERC6
-
IBM ServeRAID M1015 SAS/SATA
-
IBM ServeRAID M1115 SAS/SATA
-
IBM ServeRAID M5015 SAS/SATA
-
IBM ServeRAID M5110 SAS/SATA
-
IBM ServeRAID-MR10i
-
Intel RAID Controller SRCSAS18E
-
Intel RAID Controller SROMBSAS18E
Controllers supported by the mlx(4) driver include:
-
Mylex DAC960P
-
Mylex DAC960PD / DEC KZPSC (Fast Wide)
-
Mylex DAC960PDU
-
Mylex DAC960PL
-
Mylex DAC960PJ
-
Mylex DAC960PG
-
Mylex DAC960PU / DEC PZPAC (Ultra Wide)
-
Mylex AcceleRAID 150 (DAC960PRL)
-
Mylex AcceleRAID 250 (DAC960PTL1)
-
Mylex eXtremeRAID 1100 (DAC1164P)
-
RAIDarray 230 controllers, aka the Ultra-SCSI DEC KZPAC-AA (1-ch, 4MB cache), KZPAC-CA (3-ch, 4MB), KZPAC-CB (3-ch, 8MB cache)
All major firmware revisions (2.x, 3.x, 4.x and 5.x) are supported, however it is always advisable to upgrade to the most recent firmware available for the controller.
Compatible Mylex controllers not listed should work, but have not been verified.
Note:
[amd64, i386] Booting from these controllers is supported. EISA
adapters are not supported.
Controllers supported by the mly(4) driver include:
-
Mylex AcceleRAID 160
-
Mylex AcceleRAID 170
-
Mylex AcceleRAID 352
-
Mylex eXtremeRAID 2000
-
Mylex eXtremeRAID 3000
Compatible Mylex controllers not listed should work, but have not been verified.
These controllers are supported by the mpr(4) driver:
-
Broadcom Ltd./Avago Tech (LSI) SAS 3004 (4 Port SAS)
-
Broadcom Ltd./Avago Tech (LSI) SAS 3008 (8 Port SAS)
-
Broadcom Ltd./Avago Tech (LSI) SAS 3108 (8 Port SAS)
-
Broadcom Ltd./Avago Tech (LSI) SAS 3216 (16 Port SAS)
-
Broadcom Ltd./Avago Tech (LSI) SAS 3224 (24 Port SAS)
-
Broadcom Ltd./Avago Tech (LSI) SAS 3316 (16 Port SAS)
-
Broadcom Ltd./Avago Tech (LSI) SAS 3324 (24 Port SAS)
-
Broadcom Ltd./Avago Tech (LSI) SAS 3408 (8 Port SAS/PCIe)
-
Broadcom Ltd./Avago Tech (LSI) SAS 3416 (16 Port SAS/PCIe)
-
Broadcom Ltd./Avago Tech (LSI) SAS 3508 (8 Port SAS/PCIe)
-
Broadcom Ltd./Avago Tech (LSI) SAS 3516 (16 Port SAS/PCIe)
-
Broadcom Ltd./Avago Tech (LSI) SAS 3616 (16 Port SAS/PCIe)
-
Broadcom Ltd./Avago Tech (LSI) SAS 3708 (8 Port SAS/PCIe)
-
Broadcom Ltd./Avago Tech (LSI) SAS 3716 (16 Port SAS/PCIe)
These controllers are supported by the mps(4) driver:
-
Broadcom Ltd./Avago Tech (LSI) SAS 2004 (4 Port SAS)
-
Broadcom Ltd./Avago Tech (LSI) SAS 2008 (8 Port SAS)
-
Broadcom Ltd./Avago Tech (LSI) SAS 2108 (8 Port SAS)
-
Broadcom Ltd./Avago Tech (LSI) SAS 2116 (16 Port SAS)
-
Broadcom Ltd./Avago Tech (LSI) SAS 2208 (8 Port SAS)
-
Broadcom Ltd./Avago Tech (LSI) SAS 2308 (8 Port SAS)
-
Broadcom Ltd./Avago Tech (LSI) SSS6200 Solid State Storage
-
Intel Integrated RAID Module RMS25JB040
-
Intel Integrated RAID Module RMS25JB080
-
Intel Integrated RAID Module RMS25KB040
-
Intel Integrated RAID Module RMS25KB080
The following controllers are supported by the mpt(4) driver:
-
LSI Logic 53c1030, LSI Logic LSI2x320-X (Single and Dual Ultra320 SCSI)
-
LSI Logic AS1064, LSI Logic AS1068
-
LSI Logic FC909 (1Gb/s Fibre Channel)
-
LSI Logic FC909A (Dual 1Gb/s Fibre Channel)
-
LSI Logic FC919, LSI Logic 7102XP-LC (Single 2Gb/s Fibre Channel)
-
LSI Logic FC929, LSI Logic FC929X, LSI Logic 7202XP-LC (Dual 2Gb/s Fibre Channel)
-
LSI Logic FC949X (Dual 4Gb/s Fibre Channel)
-
LSI Logic FC949E, LSI Logic FC949ES (Dual 4Gb/s Fibre Channel PCI-Express)
The Ultra 320 SCSI controller chips supported by the mpt(4) driver can be found onboard on many systems including:
-
Dell PowerEdge 1750 thru 2850
-
IBM eServer xSeries 335
These systems also contain Integrated RAID Mirroring and Integrated RAID Mirroring Enhanced which this driver also supports.
The SAS controller chips are also present on many new AMD/Opteron based systems, like the Sun 4100. Note that this controller can drive both SAS and SATA drives or a mix of them at the same time. The Integrated RAID Mirroring available for these controllers is poorly supported at best.
The Fibre Channel controller chipset are supported by a broad variety of speeds and systems. The Apple Fibre Channel HBA is in fact the FC949ES card.
This driver also supports target mode for Fibre Channel cards. This support may be enabled by setting the desired role of the core via the LSI Logic firmware utility that establishes what roles the card can take on - no separate compilation is required.
The mrsas(4) driver supports the following hardware:
[ Thunderbolt 6Gb/s MR controller ]
-
LSI MegaRAID SAS 9265
-
LSI MegaRAID SAS 9266
-
LSI MegaRAID SAS 9267
-
LSI MegaRAID SAS 9270
-
LSI MegaRAID SAS 9271
-
LSI MegaRAID SAS 9272
-
LSI MegaRAID SAS 9285
-
LSI MegaRAID SAS 9286
-
DELL PERC H810
-
DELL PERC H710/P
[ Invader/Fury 12Gb/s MR controller ]
-
LSI MegaRAID SAS 9380
-
LSI MegaRAID SAS 9361
-
LSI MegaRAID SAS 9341
-
DELL PERC H830
-
DELL PERC H730/P
-
DELL PERC H330
The mvs(4) driver supports the following controllers:
Gen-I (SATA 1.5Gbps):
-
88SX5040
-
88SX5041
-
88SX5080
-
88SX5081
Gen-II (SATA 3Gbps, NCQ, PMP):
-
88SX6040
-
88SX6041 (including Adaptec 1420SA)
-
88SX6080
-
88SX6081
Gen-IIe (SATA 3Gbps, NCQ, PMP with FBS):
-
88SX6042
-
88SX7042 (including Adaptec 1430SA)
-
88F5182 SoC
-
88F6281 SoC
-
MV78100 SoC
Note, that this hardware supports command queueing and FIS-based switching only for ATA DMA commands. ATAPI and non-DMA ATA commands executed one by one for each port.
The ncr(4) driver provides support for the following NCR/Symbios SCSI controller chips:
-
53C810
-
53C810A
-
53C815
-
53C820
-
53C825A
-
53C860
-
53C875
-
53C875J
-
53C885
-
53C895
-
53C895A
-
53C896
-
53C1510D
The following devices are currently supported by the ncv(4) driver:
-
I-O DATA PCSC-DV
-
KME KXLC002 (TAXAN ICD-400PN, etc.), KXLC004, and UJDCD450
-
Macnica Miracle SCSI-II mPS110
-
Media Intelligent MSC-110, MSC-200
-
New Media Corporation BASICS SCSI
-
Qlogic Fast SCSI
-
RATOC REX-9530, REX-5572 (SCSI only)
Controllers supported by the nsp(4) driver include:
-
Alpha-Data AD-PCS201
-
I-O DATA CBSC16
The pms(4) driver supports the following hardware:
-
Tachyon TS Fibre Channel Card
-
Tachyon TL Fibre Channel Card
-
Tachyon XL2 Fibre Channel Card
-
Tachyon DX2 Fibre Channel Card
-
Tachyon DX2+ Fibre Channel Card
-
Tachyon DX4+ Fibre Channel Card
-
Tachyon QX2 Fibre Channel Card
-
Tachyon QX4 Fibre Channel Card
-
Tachyon DE4 Fibre Channel Card
-
Tachyon QE4 Fibre Channel Card
-
Tachyon XL10 Fibre Channel Card
-
PMC Sierra SPC SAS-SATA Card
-
PMC Sierra SPC-V SAS-SATA Card
-
PMC Sierra SPC-VE SAS-SATA Card
-
PMC Sierra SPC-V 16 Port SAS-SATA Card
-
PMC Sierra SPC-VE 16 Port SAS-SATA Card
-
PMC Sierra SPC-V SAS-SATA Card 12Gig
-
PMC Sierra SPC-VE SAS-SATA Card 12Gig
-
PMC Sierra SPC-V 16 Port SAS-SATA Card 12Gig
-
PMC Sierra SPC-VE 16 Port SAS-SATA Card 12Gig
-
Adaptec Hialeah 4/8 Port SAS-SATA HBA Card 6Gig
-
Adaptec Hialeah 4/8 Port SAS-SATA RAID Card 6Gig
-
Adaptec Hialeah 8/16 Port SAS-SATA HBA Card 6Gig
-
Adaptec Hialeah 8/16 Port SAS-SATA RAID Card 6Gig
-
Adaptec Hialeah 8/16 Port SAS-SATA HBA Encryption Card 6Gig
-
Adaptec Hialeah 8/16 Port SAS-SATA RAID Encryption Card 6Gig
-
Adaptec Delray 8 Port SAS-SATA HBA Card 12Gig
-
Adaptec Delray 8 Port SAS-SATA HBA Encryption Card 12Gig
-
Adaptec Delray 16 Port SAS-SATA HBA Card 12Gig
-
Adaptec Delray 16 Port SAS-SATA HBA Encryption Card 12Gig
The pst(4) driver supports the Promise Supertrak SX6000 ATA hardware RAID controller.
The siis(4) driver supports the following controller chips:
-
SiI3124 (PCI-X 133MHz/64bit, 4 ports)
-
SiI3131 (PCIe 1.0 x1, 1 port)
-
SiI3132 (PCIe 1.0 x1, 2 ports)
-
SiI3531 (PCIe 1.0 x1, 1 port)
Controllers supported by the stg(4) driver include:
-
Adaptec 2920/A
-
Future Domain SCSI2GO
-
Future Domain TMC-18XX/3260
-
IBM SCSI PCMCIA Card
-
ICM PSC-2401 SCSI
-
MELCO IFC-SC
-
RATOC REX-5536, REX-5536AM, REX-5536M, REX-9836A
Note that the Adaptec 2920C is supported by the ahc(4) driver.
The sym(4) driver provides support for the following Symbios/LSI Logic PCI SCSI controllers:
-
53C810
-
53C810A
-
53C815
-
53C825
-
53C825A
-
53C860
-
53C875
-
53C876
-
53C895
-
53C895A
-
53C896
-
53C897
-
53C1000
-
53C1000R
-
53C1010-33
-
53C1010-66
-
53C1510D
The SCSI controllers supported by sym(4) can be either embedded on a motherboard, or on one of the following add-on boards:
-
ASUS SC-200, SC-896
-
Data Technology DTC3130 (all variants)
-
DawiControl DC2976UW
-
Diamond FirePort (all)
-
NCR cards (all)
-
Symbios cards (all)
-
Tekram DC390W, 390U, 390F, 390U2B, 390U2W, 390U3D, and 390U3W
-
Tyan S1365
SCSI controllers supported by the trm(4) driver include:
-
Tekram DC-315 PCI Ultra SCSI adapter without BIOS and internal SCSI connector
-
Tekram DC-315U PCI Ultra SCSI adapter without BIOS
-
Tekram DC-395F PCI Ultra-Wide SCSI adapter with flash BIOS and 68-pin external SCSI connector
-
Tekram DC-395U PCI Ultra SCSI adapter with flash BIOS
-
Tekram DC-395UW PCI Ultra-Wide SCSI adapter with flash BIOS
-
Tekram DC-395U2W PCI Ultra2-Wide SCSI adapter with flash BIOS
For the Tekram DC-310/U and DC-390F/U/UW/U2B/U2W/U3W PCI SCSI host adapters, use the sym(4) driver.
The twa(4) driver supports the following SATA RAID controllers:
-
AMCC’s 3ware 9500S-4LP
-
AMCC’s 3ware 9500S-8
-
AMCC’s 3ware 9500S-8MI
-
AMCC’s 3ware 9500S-12
-
AMCC’s 3ware 9500S-12MI
-
AMCC’s 3ware 9500SX-4LP
-
AMCC’s 3ware 9500SX-8LP
-
AMCC’s 3ware 9500SX-12
-
AMCC’s 3ware 9500SX-12MI
-
AMCC’s 3ware 9500SX-16ML
-
AMCC’s 3ware 9550SX-4LP
-
AMCC’s 3ware 9550SX-8LP
-
AMCC’s 3ware 9550SX-12
-
AMCC’s 3ware 9550SX-12MI
-
AMCC’s 3ware 9550SX-16ML
-
AMCC’s 3ware 9650SE-2LP
-
AMCC’s 3ware 9650SE-4LPML
-
AMCC’s 3ware 9650SE-8LPML
-
AMCC’s 3ware 9650SE-12ML
-
AMCC’s 3ware 9650SE-16ML
-
AMCC’s 3ware 9650SE-24M8
The twe(4) driver supports the following PATA/SATA RAID controllers:
-
AMCC’s 3ware 5000 series
-
AMCC’s 3ware 6000 series
-
AMCC’s 3ware 7000-2
-
AMCC’s 3ware 7006-
-
AMCC’s 3ware 7500-4LP
-
AMCC’s 3ware 7500-8
-
AMCC’s 3ware 7500-12
-
AMCC’s 3ware 7506-4LP
-
AMCC’s 3ware 7506-8
-
AMCC’s 3ware 7506-12
-
AMCC’s 3ware 8006-2LP
-
AMCC’s 3ware 8500-4LP
-
AMCC’s 3ware 8500-8
-
AMCC’s 3ware 8500-12
-
AMCC’s 3ware 8506-4LP
-
AMCC’s 3ware 8506-8
-
AMCC’s 3ware 8506-8MI
-
AMCC’s 3ware 8506-12
-
AMCC’s 3ware 8506-12MI
The tws(4) driver supports the following SATA/SAS RAID controller:
-
LSI’s 3ware SAS 9750 series
With all supported SCSI controllers, full support is provided for SCSI-I, SCSI-II, and SCSI-III peripherals, including hard disks, optical disks, tape drives (including DAT, 8mm Exabyte, Mammoth, and DLT), medium changers, processor target devices and CD-ROM drives. WORM devices that support CD-ROM commands are supported for read-only access by the CD-ROM drivers (such as cd(4) ). WORM/CD-R/CD-RW writing support is provided by cdrecord(1) , which is a part of the sysutils/cdrtools port in the Ports Collection.
The following CD-ROM type systems are supported at this time:
Ethernet Interfaces
The ae(4) driver supports Attansic/Atheros L2 PCIe FastEthernet controllers, and is known to support the following hardware:
-
ASUS EeePC 701
-
ASUS EeePC 900
Other hardware may or may not work with this driver.
The age(4) driver provides support for LOMs based on Attansic/Atheros L1 Gigabit Ethernet controller chips, including:
-
ASUS M2N8-VMX
-
ASUS M2V
-
ASUS M3A
-
ASUS P2-M2A590G
-
ASUS P5B-E
-
ASUS P5B-MX/WIFI-AP
-
ASUS P5B-VMSE
-
ASUS P5K
-
ASUS P5KC
-
ASUS P5KPL-C
-
ASUS P5KPL-VM
-
ASUS P5K-SE
-
ASUS P5K-V
-
ASUS P5L-MX
-
ASUS P5DL2-VM
-
ASUS P5L-VM 1394
-
ASUS G2S
The ale(4) device driver provides support for the following Ethernet controllers:
-
Atheros AR8113 PCI Express Fast Ethernet controller
-
Atheros AR8114 PCI Express Fast Ethernet controller
-
Atheros AR8121 PCI Express Gigabit Ethernet controller
Adapters supported by the aue(4) driver include:
-
Abocom UFE1000, DSB650TX_NA
-
Accton USB320-EC, SpeedStream
-
ADMtek AN986, AN8511
-
Billionton USB100, USB100LP, USB100EL, USBE100
-
Corega Ether FEther USB-T, FEther USB-TX, FEther USB-TXS
-
D-Link DSB-650, DSB-650TX, DSB-650TX-PNA
-
Elecom LD-USBL/TX
-
Elsa Microlink USB2Ethernet
-
HP hn210e
-
I-O Data USB ETTX
-
Kingston KNU101TX
-
LinkSys USB10T adapters that contain the AN986 Pegasus chipset, USB10TA, USB10TX, USB100TX, USB100H1
-
MELCO LUA-TX, LUA2-TX
-
Netgear FA101
-
Planex UE-200TX
-
Sandberg USB to Network Link (model number 133-06)
-
Siemens Speedstream
-
SmartBridges smartNIC
-
SMC 2202USB
-
SOHOware NUB100
The axe(4) driver supports ASIX Electronics AX88172/AX88178/AX88772/AX88772A/AX88772B/AX88760 based USB Ethernet adapters including:
AX88172:
-
AboCom UF200
-
Acer Communications EP1427X2
-
ASIX AX88172
-
ATen UC210T
-
Billionton SnapPort
-
Billionton USB2AR
-
Buffalo (Melco Inc.) LUA-U2-KTX
-
Corega USB2_TX
-
D-Link DUBE100
-
Goodway GWUSB2E
-
JVC MP_PRX1
-
LinkSys USB200M
-
Netgear FA120
-
Sitecom LN-029
-
System TALKS Inc. SGC-X2UL
AX88178:
-
ASIX AX88178
-
Belkin F5D5055
-
Logitec LAN-GTJ/U2A
-
Buffalo (Melco Inc.) LUA3-U2-AGT
-
Planex Communications GU1000T
-
Sitecom Europe LN-028
AX88772:
-
ASIX AX88772
-
Buffalo (Melco Inc.) LUA3-U2-ATX
-
D-Link DUBE100B1
-
Planex UE-200TX-G
-
Planex UE-200TX-G2
AX88772A:
-
ASIX AX88772A
-
Cisco-Linksys USB200Mv2
AX88772B:
-
ASIX AX88772B
-
Lenovo USB 2.0 Ethernet
AX88760:
-
ASIX AX88760
ASIX Electronics AX88178A/AX88179 USB Gigabit Ethernet adapters (axge(4) driver)
The bce(4) driver provides support for various NICs based on the QLogic NetXtreme II family of Gigabit Ethernet controllers, including the following:
-
QLogic NetXtreme II BCM5706 1000Base-SX
-
QLogic NetXtreme II BCM5706 1000Base-T
-
QLogic NetXtreme II BCM5708 1000Base-SX
-
QLogic NetXtreme II BCM5708 1000Base-T
-
QLogic NetXtreme II BCM5709 1000Base-SX
-
QLogic NetXtreme II BCM5709 1000Base-T
-
QLogic NetXtreme II BCM5716 1000Base-T
-
Dell PowerEdge 1950 integrated BCM5708 NIC
-
Dell PowerEdge 2950 integrated BCM5708 NIC
-
Dell PowerEdge R710 integrated BCM5709 NIC
-
HP NC370F Multifunction Gigabit Server Adapter
-
HP NC370T Multifunction Gigabit Server Adapter
-
HP NC370i Multifunction Gigabit Server Adapter
-
HP NC371i Multifunction Gigabit Server Adapter
-
HP NC373F PCIe Multifunc Giga Server Adapter
-
HP NC373T PCIe Multifunction Gig Server Adapter
-
HP NC373i Multifunction Gigabit Server Adapter
-
HP NC373m Multifunction Gigabit Server Adapter
-
HP NC374m PCIe Multifunction Adapter
-
HP NC380T PCIe DP Multifunc Gig Server Adapter
-
HP NC382T PCIe DP Multifunction Gigabit Server Adapter
-
HP NC382i DP Multifunction Gigabit Server Adapter
-
HP NC382m DP 1GbE Multifunction BL-c Adapter
[amd64, i386] Broadcom BCM4401 based Fast Ethernet adapters (bfe(4) driver)
The bge(4) driver provides support for various NICs based on the Broadcom BCM570x family of Gigabit Ethernet controller chips, including the following:
-
3Com 3c996-SX (1000baseSX)
-
3Com 3c996-T (10/100/1000baseTX)
-
Apple Thunderbolt Display (10/100/1000baseTX)
-
Apple Thunderbolt to Gigabit Ethernet Adapter (10/100/1000baseTX)
-
Dell PowerEdge 1750 integrated BCM5704C NIC (10/100/1000baseTX)
-
Dell PowerEdge 2550 integrated BCM5700 NIC (10/100/1000baseTX)
-
Dell PowerEdge 2650 integrated BCM5703 NIC (10/100/1000baseTX)
-
Dell PowerEdge R200 integrated BCM5750 NIC (10/100/1000baseTX)
-
Dell PowerEdge R300 integrated BCM5722 NIC (10/100/1000baseTX)
-
IBM x235 server integrated BCM5703x NIC (10/100/1000baseTX)
-
HP Compaq dc7600 integrated BCM5752 NIC (10/100/1000baseTX)
-
HP ProLiant NC7760 embedded Gigabit NIC (10/100/1000baseTX)
-
HP ProLiant NC7770 PCI-X Gigabit NIC (10/100/1000baseTX)
-
HP ProLiant NC7771 PCI-X Gigabit NIC (10/100/1000baseTX)
-
HP ProLiant NC7781 embedded PCI-X Gigabit NIC (10/100/1000baseTX)
-
Netgear GA302T (10/100/1000baseTX)
-
SysKonnect SK-9D21 (10/100/1000baseTX)
-
SysKonnect SK-9D41 (1000baseSX)
The bnxt(4) driver provides support for various NICs based on the Broadcom NetXtreme-C and NetXtreme-E families of Gigabit Ethernet controller chips, including the following:
-
Broadcom BCM57301 NetXtreme-C 10Gb Ethernet Controller
-
Broadcom BCM57302 NetXtreme-C 10Gb/25Gb Ethernet Controller
-
Broadcom BCM57304 NetXtreme-C 10Gb/25Gb/40Gb/50Gb Ethernet Controller
-
Broadcom BCM57304 NetXtreme-C Ethernet Virtual Function
-
Broadcom BCM57314 NetXtreme-C Ethernet Virtual Function
-
Broadcom BCM57402 NetXtreme-E 10Gb Ethernet Controller
-
Broadcom BCM57402 NetXtreme-E Ethernet Partition
-
Broadcom BCM57404 NetXtreme-E 10Gb/25Gb Ethernet Controller
-
Broadcom BCM57404 NetXtreme-E Ethernet Virtual Function
-
Broadcom BCM57404 NetXtreme-E Partition
-
Broadcom BCM57406 NetXtreme-E 10GBASE-T Ethernet Controller
-
Broadcom BCM57406 NetXtreme-E Partition
-
Broadcom BCM57407 NetXtreme-E 10GBase-T Ethernet Controller
-
Broadcom BCM57407 NetXtreme-E 25Gb Ethernet Controller
-
Broadcom BCM57407 NetXtreme-E Partition
-
Broadcom BCM57412 NetXtreme-E Partition
-
Broadcom BCM57414 NetXtreme-E Ethernet Virtual Function
-
Broadcom BCM57414 NetXtreme-E Partition
-
Broadcom BCM57416 NetXtreme-E Partition
-
Broadcom BCM57417 NetXtreme-E Ethernet Partition
-
Broadcom BCM57454 NetXtreme-E 10Gb/25Gb/40Gb/50Gb/100Gb Ethernet
The bxe(4) driver provides support for various NICs based on the QLogic NetXtreme II family of 10Gb Ethernet controller chips, including the following:
-
QLogic NetXtreme II BCM57710 10Gb
-
QLogic NetXtreme II BCM57711 10Gb
-
QLogic NetXtreme II BCM57711E 10Gb
-
QLogic NetXtreme II BCM57712 10Gb
-
QLogic NetXtreme II BCM57712-MF 10Gb
-
QLogic NetXtreme II BCM57800 10Gb
-
QLogic NetXtreme II BCM57800-MF 10Gb
-
QLogic NetXtreme II BCM57810 10Gb
-
QLogic NetXtreme II BCM57810-MF 10Gb
-
QLogic NetXtreme II BCM57840 10Gb / 20Gb
-
QLogic NetXtreme II BCM57840-MF 10Gb
The chips supported by the cas(4) driver are:
-
National Semiconductor DP83065 Saturn Gigabit Ethernet
-
Sun Cassini Gigabit Ethernet
-
Sun Cassini+ Gigabit Ethernet
The following add-on cards are known to work with the cas(4) driver at this time:
-
Sun GigaSwift Ethernet 1.0 MMF (Cassini Kuheen) (part no. 501-5524)
-
Sun GigaSwift Ethernet 1.0 UTP (Cassini) (part no. 501-5902)
-
Sun GigaSwift Ethernet UTP (GCS) (part no. 501-6719)
-
Sun Quad GigaSwift Ethernet UTP (QGE) (part no. 501-6522)
-
Sun Quad GigaSwift Ethernet PCI-X (QGE-X) (part no. 501-6738)
The following devices are supported by the cdce(4) driver:
-
Prolific PL-2501 Host-to-Host Bridge Controller
-
Sharp Zaurus PDA
-
Terayon TJ-715 DOCSIS Cable Modem
The cue(4) driver supports CATC USB-EL1210A based USB Ethernet adapters including:
-
Belkin F5U011/F5U111
-
CATC Netmate
-
CATC Netmate II
-
SmartBridges SmartLink
The cxgb(4) driver supports 10 Gigabit and 1 Gigabit Ethernet adapters based on the T3 and T3B chipset:
-
Chelsio 10GBase-CX4
-
Chelsio 10GBase-LR
-
Chelsio 10GBase-SR
The cxgbe(4) driver supports 100Gb and 25Gb Ethernet adapters based on the T6 ASIC:
-
Chelsio T6225-CR
-
Chelsio T6225-SO-CR
-
Chelsio T62100-LP-CR
-
Chelsio T62100-SO-CR
-
Chelsio T62100-CR
The cxgbe(4) driver supports 40Gb, 10Gb and 1Gb Ethernet adapters based on the T5 ASIC:
-
Chelsio T580-CR
-
Chelsio T580-LP-CR
-
Chelsio T580-LP-SO-CR
-
Chelsio T560-CR
-
Chelsio T540-CR
-
Chelsio T540-LP-CR
-
Chelsio T522-CR
-
Chelsio T520-LL-CR
-
Chelsio T520-CR
-
Chelsio T520-SO
-
Chelsio T520-BT
-
Chelsio T504-BT
The cxgbe(4) driver supports 10Gb and 1Gb Ethernet adapters based on the T4 ASIC:
-
Chelsio T420-CR
-
Chelsio T422-CR
-
Chelsio T440-CR
-
Chelsio T420-BCH
-
Chelsio T440-BCH
-
Chelsio T440-CH
-
Chelsio T420-SO
-
Chelsio T420-CX
-
Chelsio T420-BT
-
Chelsio T404-BT
The dc(4) driver provides support for the following chipsets:
-
DEC/Intel 21143
-
ADMtek AL981 Comet, AN985 Centaur, ADM9511 Centaur II and ADM9513 Centaur II
-
ALi/ULi M5261 and M5263
-
ASIX Electronics AX88140A and AX88141
-
Conexant LANfinity RS7112 (miniPCI)
-
Davicom DM9009, DM9100, DM9102 and DM9102A
-
Lite-On 82c168 and 82c169 PNIC
-
Lite-On/Macronix 82c115 PNIC II
-
Macronix 98713, 98713A, 98715, 98715A, 98715AEC-C, 98725, 98727 and 98732
-
Xircom X3201 (cardbus only)
The following NICs are known to work with the dc(4) driver at this time:
-
3Com OfficeConnect 10/100B (ADMtek AN985 Centaur-P)
-
Abocom FE2500
-
Accton EN1217 (98715A)
-
Accton EN2242 MiniPCI
-
Adico AE310TX (98715A)
-
Alfa Inc GFC2204 (ASIX AX88140A)
-
Built in 10Mbps only Ethernet on Compaq Presario 7900 series desktops (21143, non-MII)
-
Built in Sun DMFE 10/100 Mbps Ethernet on Sun Netra X1 and Sun Fire V100 (DM9102A, MII)
-
Built in Ethernet on LinkSys EtherFast 10/100 Instant GigaDrive (DM9102, MII)
-
CNet Pro110B (ASIX AX88140A)
-
CNet Pro120A (98715A or 98713A) and CNet Pro120B (98715)
-
Compex RL100-TX (98713 or 98713A)
-
D-Link DFE-570TX (21143, MII, quad port)
-
Digital DE500-BA 10/100 (21143, non-MII)
-
ELECOM Laneed LD-CBL/TXA (ADMtek AN985)
-
Hawking CB102 CardBus
-
IBM EtherJet Cardbus Adapter
-
Intel PRO/100 Mobile Cardbus (versions that use the X3201 chipset)
-
Jaton XpressNet (Davicom DM9102)
-
Kingston KNE100TX (21143, MII)
-
Kingston KNE110TX (PNIC 82c169)
-
LinkSys LNE100TX (PNIC 82c168, 82c169)
-
LinkSys LNE100TX v2.0 (PNIC II 82c115)
-
LinkSys LNE100TX v4.0/4.1 (ADMtek AN985 Centaur-P)
-
Matrox FastNIC 10/100 (PNIC 82c168, 82c169)
-
Melco LGY-PCI-TXL
-
Microsoft MN-120 10/100 CardBus (ADMTek Centaur-C)
-
Microsoft MN-130 10/100 PCI (ADMTek Centaur-P)
-
NDC SOHOware SFA110A (98713A)
-
NDC SOHOware SFA110A Rev B4 (98715AEC-C)
-
NetGear FA310-TX Rev. D1, D2 or D3 (PNIC 82c169)
-
Netgear FA511
-
PlaneX FNW-3602-T (ADMtek AN985)
-
SMC EZ Card 10/100 1233A-TX (ADMtek AN985)
-
SVEC PN102-TX (98713)
-
Xircom Cardbus Realport
-
Xircom Cardbus Ethernet 10/100
-
Xircom Cardbus Ethernet II 10/100
The em(4) driver supports Gigabit Ethernet adapters based on the Intel 82540, 82541ER, 82541PI, 82542, 82543, 82544, 82545, 82546, 82546EB, 82546GB, 82547, 82571, 82572, 82573, 82574, 82575, 82576, and 82580 controller chips:
-
Intel Gigabit ET Dual Port Server Adapter (82576)
-
Intel Gigabit VT Quad Port Server Adapter (82575)
-
Intel Single, Dual and Quad Gigabit Ethernet Controller (82580)
-
Intel i210 and i211 Gigabit Ethernet Controller
-
Intel i350 and i354 Gigabit Ethernet Controller
-
Intel PRO/1000 CT Network Connection (82547)
-
Intel PRO/1000 F Server Adapter (82543)
-
Intel PRO/1000 Gigabit Server Adapter (82542)
-
Intel PRO/1000 GT Desktop Adapter (82541PI)
-
Intel PRO/1000 MF Dual Port Server Adapter (82546)
-
Intel PRO/1000 MF Server Adapter (82545)
-
Intel PRO/1000 MF Server Adapter (LX) (82545)
-
Intel PRO/1000 MT Desktop Adapter (82540)
-
Intel PRO/1000 MT Desktop Adapter (82541)
-
Intel PRO/1000 MT Dual Port Server Adapter (82546)
-
Intel PRO/1000 MT Quad Port Server Adapter (82546EB)
-
Intel PRO/1000 MT Server Adapter (82545)
-
Intel PRO/1000 PF Dual Port Server Adapter (82571)
-
Intel PRO/1000 PF Quad Port Server Adapter (82571)
-
Intel PRO/1000 PF Server Adapter (82572)
-
Intel PRO/1000 PT Desktop Adapter (82572)
-
Intel PRO/1000 PT Dual Port Server Adapter (82571)
-
Intel PRO/1000 PT Quad Port Server Adapter (82571)
-
Intel PRO/1000 PT Server Adapter (82572)
-
Intel PRO/1000 T Desktop Adapter (82544)
-
Intel PRO/1000 T Server Adapter (82543)
-
Intel PRO/1000 XF Server Adapter (82544)
-
Intel PRO/1000 XT Server Adapter (82544)
Agere ET1310 Gigabit Ethernet adapters (et(4) driver)
Adapters supported by the fxp(4) driver include:
-
Intel EtherExpress PRO/10
-
Intel InBusiness 10/100
-
Intel PRO/100B / EtherExpressPRO/100 B PCI Adapter
-
Intel PRO/100+ Management Adapter
-
Intel PRO/100 VE Desktop Adapter
-
Intel PRO/100 VM Network Connection
-
Intel PRO/100 M Desktop Adapter
-
Intel PRO/100 S Desktop, Server and Dual-Port Server Adapters
-
Many on-board network interfaces on Intel motherboards
Chips supported by the gem(4) driver include:
-
Apple GMAC
-
Sun ERI 10/100 Mbps Ethernet
-
Sun GEM Gigabit Ethernet
The following add-on cards are known to work with the gem(4) driver at this time:
-
Sun Gigabit Ethernet PCI 2.0/3.0 (GBE/P) (part no. 501-4373)
-
Sun Gigabit Ethernet SBus 2.0/3.0 (GBE/S) (part no. 501-4375)
The following devices are supported by the ipheth(4) driver:
-
Apple iPhone tethering (all models)
-
Apple iPad tethering (all models)
The ixgbe(4) driver supports the following cards:
-
Intel® 10 Gigabit XF SR/AF Dual Port Server Adapter
-
Intel® 10 Gigabit XF SR/LR Server Adapter
-
Intel® 82598EB 10 Gigabit AF Network Connection
-
Intel® 82598EB 10 Gigabit AT CX4 Network Connection
Most adapters in the Intel Ethernet 700 Series with SFP+/SFP28/QSFP+ cages have firmware that requires that Intel qualified modules are used; these qualified modules are listed below. This qualification check cannot be disabled by the driver.
The ixl(4) driver supports 40Gb Ethernet adapters with these QSFP+ modules:
-
Intel 4x10G/40G QSFP+ 40GBASE-SR4 E40GQSFPSR
-
Intel 4x10G/40G QSFP+ 40GBASE-LR4 E40GQSFPLR
The ixl(4) driver supports 25Gb Ethernet adapters with these SFP28 modules:
-
Intel 10G/25G SFP28 25GBASE-SR E25GSFP28SR
-
Intel 10G/25G SFP28 25GBASE-SR E25GSFP28SRX (Extended Temp)
The ixl(4) driver supports 25Gb and 10Gb Ethernet adapters with these SFP+ modules:
-
Intel 1G/10G SFP+ SR FTLX8571D3BCV-IT
-
Intel 1G/10G SFP+ SR AFBR-703SDZ-IN2
-
Intel 1G/10G SFP+ LR FTLX1471D3BCV-IT
-
Intel 1G/10G SFP+ LR AFCT-701SDZ-IN2
-
Intel 1G/10G SFP+ 10GBASE-SR E10GSFPSR
-
Intel 10G SFP+ 10GBASE-SR E10GSFPSRX (Extended Temp)
-
Intel 1G/10G SFP+ 10GBASE-LR E10GSFPLR
Note that adapters also support all passive and active limiting direct attach cables that comply with SFF-8431 v4.1 and SFF-8472 v10.4 specifications.
This is not an exhaustive list; please consult product documentation for an up-to-date list of supported media.
The jme(4) device driver provides support for the following Ethernet controllers:
-
JMicron JMC250 PCI Express Gigabit Ethernet controller
-
JMicron JMC251 PCI Express Gigabit Ethernet with Card Read Host controller
-
JMicron JMC260 PCI Express Fast Ethernet controller
-
JMicron JMC261 PCI Express Gigabit Ethernet with Card Read Host controller
The kue(4) driver supports Kawasaki LSI KL5KLUSB101B based USB Ethernet adapters including:
-
3Com 3c19250
-
3Com 3c460 HomeConnect Ethernet USB Adapter
-
ADS Technologies USB-10BT
-
AOX USB101
-
ATen UC10T
-
Abocom URE 450
-
Corega USB-T
-
D-Link DSB-650C
-
Entrega NET-USB-E45, NET-HUB-3U1E
-
I/O Data USB ETT
-
Kawasaki DU-H3E
-
LinkSys USB10T
-
Netgear EA101
-
Peracom USB Ethernet Adapter
-
Psion Gold Port USB Ethernet adapter
-
SMC 2102USB, 2104USB
Adapters supported by the lge(4) driver include:
-
SMC TigerCard 1000 (SMC9462SX)
-
D-Link DGE-500SX
The mlx4en(4) driver supports the following network adapters:
-
Mellanox ConnectX-2 (ETH)
-
Mellanox ConnectX-3 (ETH)
The mlx5en(4) driver supports 100Gb, 50Gb, 40Gb, 25Gb and 10Gb Ethernet adapters. ConnectX-5 supports:10/20/25/40/50/56/100Gb/s speeds. ConnectX-4 supports:10/20/25/40/50/56/100Gb/s speeds. ConnectX-4 LX supports:10/25/40/50Gb/s speeds (and reduced power consumption) :
-
Mellanox MCX455A-ECAT
-
Mellanox MCX456A-ECAT
-
Mellanox MCX415A-CCAT
-
Mellanox MCX416A-CCAT
-
Mellanox MCX455A-FCAT
-
Mellanox MCX456A-FCAT
-
Mellanox MCX415A-BCAT
-
Mellanox MCX416A-BCAT
-
Mellanox MCX4131A-GCAT
-
Mellanox MCX4131A-BCAT
-
Mellanox MCX4121A-ACAT
-
Mellanox MCX4111A-ACAT
-
Mellanox MCX4121A-XCAT
-
Mellanox MCX4111A-XCAT
The msk(4) driver provides support for various NICs based on the Marvell/SysKonnect Yukon II based Gigabit Ethernet controller chips, including:
-
D-Link 550SX Gigabit Ethernet
-
D-Link 560SX Gigabit Ethernet
-
D-Link 560T Gigabit Ethernet
-
Marvell Yukon 88E8021CU Gigabit Ethernet
-
Marvell Yukon 88E8021 SX/LX Gigabit Ethernet
-
Marvell Yukon 88E8022CU Gigabit Ethernet
-
Marvell Yukon 88E8022 SX/LX Gigabit Ethernet
-
Marvell Yukon 88E8061CU Gigabit Ethernet
-
Marvell Yukon 88E8061 SX/LX Gigabit Ethernet
-
Marvell Yukon 88E8062CU Gigabit Ethernet
-
Marvell Yukon 88E8062 SX/LX Gigabit Ethernet
-
Marvell Yukon 88E8035 Fast Ethernet
-
Marvell Yukon 88E8036 Fast Ethernet
-
Marvell Yukon 88E8038 Fast Ethernet
-
Marvell Yukon 88E8039 Fast Ethernet
-
Marvell Yukon 88E8040 Fast Ethernet
-
Marvell Yukon 88E8040T Fast Ethernet
-
Marvell Yukon 88E8042 Fast Ethernet
-
Marvell Yukon 88E8048 Fast Ethernet
-
Marvell Yukon 88E8050 Gigabit Ethernet
-
Marvell Yukon 88E8052 Gigabit Ethernet
-
Marvell Yukon 88E8053 Gigabit Ethernet
-
Marvell Yukon 88E8055 Gigabit Ethernet
-
Marvell Yukon 88E8056 Gigabit Ethernet
-
Marvell Yukon 88E8057 Gigabit Ethernet
-
Marvell Yukon 88E8058 Gigabit Ethernet
-
Marvell Yukon 88E8059 Gigabit Ethernet
-
Marvell Yukon 88E8070 Gigabit Ethernet
-
Marvell Yukon 88E8071 Gigabit Ethernet
-
Marvell Yukon 88E8072 Gigabit Ethernet
-
Marvell Yukon 88E8075 Gigabit Ethernet
-
SysKonnect SK-9Sxx Gigabit Ethernet
-
SysKonnect SK-9Exx Gigabit Ethernet
The mxge(4) driver supports 10 Gigabit Ethernet adapters based on the Myricom LANai Z8E chips:
-
Myricom 10GBase-CX4 (10G-PCIE-8A-C, 10G-PCIE-8AL-C)
-
Myricom 10GBase-R (10G-PCIE-8A-R, 10G-PCIE-8AL-R)
-
Myricom 10G XAUI over ribbon fiber (10G-PCIE-8A-Q, 10G-PCIE-8AL-Q)
The my(4) driver provides support for various NICs based on the Myson chipset. Supported models include:
-
Myson MTD800 PCI Fast Ethernet chip
-
Myson MTD803 PCI Fast Ethernet chip
-
Myson MTD89X PCI Gigabit Ethernet chip
The nfe(4) driver supports the following NVIDIA MCP onboard adapters:
-
NVIDIA nForce MCP Networking Adapter
-
NVIDIA nForce MCP04 Networking Adapter
-
NVIDIA nForce 430 MCP12 Networking Adapter
-
NVIDIA nForce 430 MCP13 Networking Adapter
-
NVIDIA nForce MCP51 Networking Adapter
-
NVIDIA nForce MCP55 Networking Adapter
-
NVIDIA nForce MCP61 Networking Adapter
-
NVIDIA nForce MCP65 Networking Adapter
-
NVIDIA nForce MCP67 Networking Adapter
-
NVIDIA nForce MCP73 Networking Adapter
-
NVIDIA nForce MCP77 Networking Adapter
-
NVIDIA nForce MCP79 Networking Adapter
-
NVIDIA nForce2 MCP2 Networking Adapter
-
NVIDIA nForce2 400 MCP4 Networking Adapter
-
NVIDIA nForce2 400 MCP5 Networking Adapter
-
NVIDIA nForce3 MCP3 Networking Adapter
-
NVIDIA nForce3 250 MCP6 Networking Adapter
-
NVIDIA nForce3 MCP7 Networking Adapter
-
NVIDIA nForce4 CK804 MCP8 Networking Adapter
-
NVIDIA nForce4 CK804 MCP9 Networking Adapter
The nge(4) driver supports National Semiconductor DP83820 and DP83821 based Gigabit Ethernet adapters including:
-
Addtron AEG320T
-
Ark PC SOHO-GA2500T (32-bit PCI) and SOHO-GA2000T (64-bit PCI)
-
Asante FriendlyNet GigaNIX 1000TA and 1000TPC
-
D-Link DGE-500T
-
Linksys EG1032, revision 1
-
Netgear GA621
-
Netgear GA622T
-
SMC EZ Card 1000 (SMC9462TX)
-
Surecom Technology EP-320G-TX
-
Trendware TEG-PCITX (32-bit PCI) and TEG-PCITX2 (64-bit PCI)
The oce(4) driver supports the following network adapters:
-
Emulex BladeEngine 2
-
Emulex BladeEngine 3
-
Emulex Lancer
The qlxgb(4) driver supports 10 Gigabit Ethernet & CNA Adapter based on the following chipsets:
-
QLogic 3200 series
-
QLogic 8200 series
The qlxgbe(4) driver supports 10 Gigabit Ethernet & CNA Adapter based on the following chipsets:
-
QLogic 8300 series
The qlxge(4) driver supports 10 Gigabit Ethernet & CNA Adapter based on the following chipsets:
-
QLogic 8100 series
The re(4) driver supports RealTek RTL8139C+, RTL8169, RTL816xS, RTL811xS, RTL8168, RTL810xE and RTL8111 based Fast Ethernet and Gigabit Ethernet adapters including:
-
Alloy Computer Products EtherGOLD 1439E 10/100 (8139C+)
-
Compaq Evo N1015v Integrated Ethernet (8139C+)
-
Corega CG-LAPCIGT Gigabit Ethernet (8169S)
-
D-Link DGE-528(T) Gigabit Ethernet (8169S)
-
Gigabyte 7N400 Pro2 Integrated Gigabit Ethernet (8110S)
-
LevelOne GNC-0105T (8169S)
-
LinkSys EG1032 (32-bit PCI)
-
PLANEX COMMUNICATIONS Inc. GN-1200TC (8169S)
-
TP-Link TG-3468 v2 Gigabit Ethernet (8168)
-
USRobotics USR997902 Gigabit Ethernet (8169S)
-
Xterasys XN-152 10/100/1000 NIC (8169)
Adapters supported by the rl(4) driver include:
-
Accton “Cheetah” EN1207D (MPX 5030/5038; RealTek 8139 clone)
-
Allied Telesyn AT2550
-
Allied Telesyn AT2500TX
-
Belkin F5D5000
-
BUFFALO (Melco INC.) LPC-CB-CLX (CardBus)
-
Compaq HNE-300
-
CompUSA no-name 10/100 PCI Ethernet NIC
-
Corega FEther CB-TXD
-
Corega FEtherII CB-TXD
-
D-Link DFE-520TX (rev. C1)
-
D-Link DFE-528TX
-
D-Link DFE-530TX+
-
D-Link DFE-538TX
-
D-Link DFE-690TXD
-
Edimax EP-4103DL CardBus
-
Encore ENL832-TX 10/100 M PCI
-
Farallon NetLINE 10/100 PCI
-
Genius GF100TXR
-
GigaFast Ethernet EE100-AXP
-
KTX-9130TX 10/100 Fast Ethernet
-
LevelOne FPC-0106TX
-
Longshine LCS-8038TX-R
-
NDC Communications NE100TX-E
-
Netronix Inc. EA-1210 NetEther 10/100
-
Nortel Networks 10/100BaseTX
-
OvisLink LEF-8129TX
-
OvisLink LEF-8139TX
-
Peppercon AG ROL-F
-
Planex FNW-3603-TX
-
Planex FNW-3800-TX
-
SMC EZ Card 10/100 PCI 1211-TX
-
SOHO (PRAGMATIC) UE-1211C
The rue(4) driver supports RealTek RTL8150 based USB Ethernet adapters including:
-
Buffalo (Melco Inc.) LUA-KTX
-
Green House GH-USB100B
-
LinkSys USB100M
-
Billionton 10/100 FastEthernet USBKR2
The sfxge(4) driver supports all 10Gb Ethernet adapters based on Solarflare SFC9000 family controllers.
The sge(4) device driver provides support for the following Ethernet controllers:
-
SiS190 Fast Ethernet controller
-
SiS191 Fast/Gigabit Ethernet controller
The sis(4) driver supports Silicon Integrated Systems SiS 900 and SiS 7016 based Fast Ethernet adapters and embedded controllers, as well as Fast Ethernet adapters based on the National Semiconductor DP83815 (MacPhyter) and DP83816 chips. Supported adapters include:
-
@Nifty FNECHARD IFC USUP-TX
-
MELCO LGY-PCI-TXC
-
Netgear FA311-TX (DP83815)
-
Netgear FA312-TX (DP83815)
-
SiS 630, 635, and 735 motherboard chipsets
-
Soekris Engineering net45xx, net48xx, lan1621, and lan1641
Adapters supported by the sk(4) driver include:
-
3Com 3C940 single port, 1000baseT adapter
-
3Com 3C2000-T single port, 1000baseT adapter
-
Belkin F5D5005 single port, 1000baseT adapter
-
D-Link DGE-530T single port, 1000baseT adapter
-
Linksys (revision 2) single port, 1000baseT adapter
-
SK-9521 SK-NET GE-T single port, 1000baseT adapter
-
SK-9821 SK-NET GE-T single port, 1000baseT adapter
-
SK-9822 SK-NET GE-T dual port, 1000baseT adapter
-
SK-9841 SK-NET GE-LX single port, single mode fiber adapter
-
SK-9842 SK-NET GE-LX dual port, single mode fiber adapter
-
SK-9843 SK-NET GE-SX single port, multimode fiber adapter
-
SK-9844 SK-NET GE-SX dual port, multimode fiber adapter
-
SMC 9452TX single port, 1000baseT adapter
The following devices are supported by the smsc(4) driver:
-
SMSC LAN9500, LAN9500A, LAN9505 and LAN9505A based Ethernet adapters
-
SMSC LAN89530, LAN9530 and LAN9730 based Ethernet adapters
-
SMSC LAN951x Ethernet adapters with integrated USB hub
The ste(4) driver supports Sundance Technologies ST201 based Fast Ethernet adapters and embedded controllers including:
-
D-Link DFE-530TXS
-
D-Link DFE-550TX
-
D-Link DFE-580TX
The stge(4) driver provides support for various NICs based on the Sundance/Tamarack TC9021 based Gigabit Ethernet controller chips, including:
-
Antares Microsystems Gigabit Ethernet
-
ASUS NX1101 Gigabit Ethernet
-
D-Link DL-4000 Gigabit Ethernet
-
IC Plus IP1000A Gigabit Ethernet
-
Sundance ST-2021 Gigabit Ethernet
-
Sundance ST-2023 Gigabit Ethernet
-
Sundance TC9021 Gigabit Ethernet
-
Tamarack TC9021 Gigabit Ethernet
The ti(4) driver supports Gigabit Ethernet adapters based on the Alteon Tigon I and II chips. The ti(4) driver has been tested with the following adapters:
-
3Com 3c985-SX Gigabit Ethernet adapter (Tigon 1)
-
3Com 3c985B-SX Gigabit Ethernet adapter (Tigon 2)
-
Alteon AceNIC V Gigabit Ethernet adapter (1000baseSX)
-
Alteon AceNIC V Gigabit Ethernet adapter (1000baseT)
-
Digital EtherWORKS 1000SX PCI Gigabit adapter
-
Netgear GA620 Gigabit Ethernet adapter (1000baseSX)
-
Netgear GA620T Gigabit Ethernet adapter (1000baseT)
The following adapters should also be supported but have not yet been tested:
-
Asante GigaNIX1000T Gigabit Ethernet adapter
-
Asante PCI 1000BASE-SX Gigabit Ethernet adapter
-
Farallon PN9000SX Gigabit Ethernet adapter
-
NEC Gigabit Ethernet
-
Silicon Graphics PCI Gigabit Ethernet adapter
The udav(4) driver supports the following adapters:
-
Corega FEther USB-TXC
-
ShanTou ST268 USB NIC
The urndis(4) driver supports the functionality of many Android devices.
The vge(4) driver supports VIA Networking VT6120, VT6122, VT6130 and VT6132 based Gigabit Ethernet adapters including:
-
VIA Networking LAN-on-motherboard Gigabit Ethernet
-
ZyXEL GN650-T 64-bit PCI Gigabit Ethernet NIC (ZX1701)
-
ZyXEL GN670-T 32-bit PCI Gigabit Ethernet NIC (ZX1702)
The vr(4) driver supports VIA Technologies Rhine I, Rhine II, and Rhine III based Fast Ethernet adapters including:
-
AOpen/Acer ALN-320
-
D-Link DFE520-TX
-
D-Link DFE530-TX
-
Hawking Technologies PN102TX
-
Soekris Engineering net5501
The vte(4) device driver provides support for the following Ethernet controllers:
-
DM&P Vortex86 RDC R6040 Fast Ethernet controller
The xl(4) driver supports the following hardware:
-
3Com 3c900-TPO
-
3Com 3c900-COMBO
-
3Com 3c905-TX
-
3Com 3c905-T4
-
3Com 3c900B-TPO
-
3Com 3c900B-TPC
-
3Com 3c900B-FL
-
3Com 3c900B-COMBO
-
3Com 3c905B-T4
-
3Com 3c905B-TX
-
3Com 3c905B-FX
-
3Com 3c905B-COMBO
-
3Com 3c905C-TX
-
3Com 3c980, 3c980B, and 3c980C server adapters
-
3Com 3cSOHO100-TX OfficeConnect adapters
-
3Com 3c450 HomeConnect adapters
-
3Com 3c555, 3c556 and 3c556B mini-PCI adapters
-
3Com 3C3SH573BT, 3C575TX, 3CCFE575BT, 3CXFE575BT, 3CCFE575CT, 3CXFE575CT, 3CCFEM656, 3CCFEM656B, and 3CCFEM656C, 3CXFEM656, 3CXFEM656B, and 3CXFEM656C CardBus adapters
-
3Com 3c905-TX, 3c905B-TX 3c905C-TX, 3c920B-EMB, and 3c920B-EMB-WNM embedded adapters
Both the 3C656 family of CardBus cards and the 3C556 family of MiniPCI cards have a built-in proprietary modem. Neither the xl(4) driver nor any other FreeBSD driver supports this modem.
Wireless Network Interfaces
[amd64, i386] Cisco/Aironet 802.11b wireless adapters (4an(4) driver)
The ath(4) driver supports all Atheros Cardbus and PCI cards, except those that are based on the AR5005VL chipset.
The bwi(4) driver supports Broadcom BCM43xx based wireless devices, including:
-
Apple Airport Extreme
-
Apple Airport Extreme
-
ASUS WL-100g
-
ASUS WL-138g
-
Buffalo WLI-CB-G54S
-
Buffalo WLI-PCI-G54S
-
Compaq R4035 onboard
-
Dell Wireless 1390
-
Dell Wireless 1470
-
Dell Truemobile 1300 r2
-
Dell Truemobile 1400
-
HP nx6125
-
Linksys WPC54G Ver 3
-
Linksys WPC54GS Ver 2
-
TRENDnet TEW-401PCplus
-
US Robotics 5411
The bwi(4) driver uses the older v3 version of Broadcom’s firmware. While this older firmware does support most BCM43xx parts, the bwn(4) driver works better for the newer chips it supports. You must use the bwi(4) driver if you are using older Broadcom chipsets (BCM4301, BCM4303 and BCM4306 rev 2). The v4 version of the firmware that bwn(4) uses does not support these chips.
The bwn(4) driver supports Broadcom BCM43xx based wireless devices, including:
-
Apple Airport Extreme
-
ASUS WL-138g
-
Buffalo WLI-CB-G54S
-
Dell Wireless 1390
-
Dell Wireless 1470
-
Dell Truemobile 1400
-
HP Compaq 6715b
-
HP nx6125
-
Linksys WPC54G Ver 3
-
Linksys WPC54GS Ver 2
-
US Robotics 5411
[i386, amd64] Intel PRO/Wireless 2100 MiniPCI network adapter (ipw(4) driver)
[i386, amd64] Intel PRO/Wireless 2200BG/2915ABG MiniPCI and 2225BG PCI network adapters (iwi(4) driver)
[i386, amd64] Intel Dual Band Wireless AC 3160/7260/7265 IEEE 802.11ac network adapters (iwn(4) driver)
[i386, amd64] Intel Wireless WiFi Link 4965AGN IEEE 802.11n PCI network adapters (iwn(4) driver)
[i386, amd64] Marvell Libertas IEEE 802.11b/g PCI network adapters (malo(4) driver)
Marvell 88W8363 IEEE 802.11n wireless network adapters (mwl(4) driver)
The otus(4) driver provices support for Atheros AR9170 USB IEEE 802.11b/g/n wireless network adapters, including:
-
3Com 3CRUSBN275
-
Arcadyan WN7512
-
CACE AirPcap Nx
-
D-Link DWA-130 rev D1
-
D-Link DWA-160 rev A1
-
D-Link DWA-160 rev A2
-
IO-Data WN-GDN/US2
-
NEC Aterm WL300NU-G
-
Netgear WNDA3100
-
Netgear WN111 v2
-
Planex GW-US300
-
SMC Networks SMCWUSB-N2
-
TP-Link TL-WN821N v1, v2
-
Ubiquiti SR71 USB
-
Unex DNUA-81
-
Z-Com UB81
-
Z-Com UB82
-
ZyXEL NWD-271N
The ral(4) driver supports PCI/PCIe/CardBus wireless adapters based on Ralink Technology chipsets, including:
-
A-Link WL54H
-
A-Link WL54PC
-
AirLink101 AWLC5025
-
AirLink101 AWLH5025
-
Amigo AWI-914W
-
Amigo AWI-922W
-
Amigo AWI-926W
-
AMIT WL531C
-
AMIT WL531P
-
AOpen AOI-831
-
ASUS WL-107G
-
ASUS WL-130g
-
Atlantis Land A02-PCI-W54
-
Atlantis Land A02-PCM-W54
-
Belkin F5D7000 v3
-
Belkin F5D7010 v2
-
Billionton MIWLGRL
-
Canyon CN-WF511
-
Canyon CN-WF513
-
CC&C WL-2102
-
CNet CWC-854
-
CNet CWP-854
-
Compex WL54G
-
Compex WLP54G
-
Conceptronic C54RC
-
Conceptronic C54Ri
-
D-Link DWA-525 rev A2
-
Digitus DN-7001G-RA
-
Digitus DN-7006G-RA
-
E-Tech WGPC02
-
E-Tech WGPI02
-
Edimax EW-7108PCg
-
Edimax EW-7128g
-
Eminent EM3036
-
Eminent EM3037
-
Encore ENLWI-G-RLAM
-
Encore ENPWI-G-RLAM
-
Fiberline WL-400P
-
Fibreline WL-400X
-
Gigabyte GN-WI01GS
-
Gigabyte GN-WIKG
-
Gigabyte GN-WMKG
-
Gigabyte GN-WP01GS
-
Gigabyte GN-WPKG
-
Hawking HWC54GR
-
Hawking HWP54GR
-
iNexQ CR054g-009 (R03)
-
JAHT WN-4054P
-
JAHT WN-4054PCI
-
LevelOne WNC-0301 v2
-
LevelOne WPC-0301 v2
-
Linksys WMP54G v4
-
Micronet SP906GK
-
Micronet SP908GK V3
-
Minitar MN54GCB-R
-
Minitar MN54GPC-R
-
MSI CB54G2
-
MSI MP54G2
-
MSI PC54G2
-
OvisLink EVO-W54PCI
-
PheeNet HWL-PCIG/RA
-
Planex GW-NS300N
-
Pro-Nets CB80211G
-
Pro-Nets PC80211G
-
Repotec RP-WB7108
-
Repotec RP-WP0854
-
SATech SN-54C
-
SATech SN-54P
-
Sitecom WL-112
-
Sitecom WL-115
-
SMC SMCWCB-GM
-
SMC SMCWPCI-GM
-
SparkLAN WL-685R
-
Surecom EP-9321-g
-
Surecom EP-9321-g1
-
Surecom EP-9428-g
-
Sweex LC500050
-
Sweex LC700030
-
TekComm NE-9321-g
-
TekComm NE-9428-g
-
Unex CR054g-R02
-
Unex MR054g-R02
-
Zinwell ZWX-G160
-
Zinwell ZWX-G360
-
Zinwell ZWX-G361
-
Zonet ZEW1500
-
Zonet ZEW1600
The rsu(4) driver provices support for Realtek RTL8188SU/RTL8192SU USB IEEE 802.11b/g/n wireless network adapters, including:
-
ASUS USB-N10
-
Belkin F7D1101 v1
-
D-Link DWA-131 A1
-
EDUP EP-MS150N(W)
-
Edimax EW-7622UMN
-
Hercules HWGUn-54
-
Hercules HWNUm-300
-
Planex GW-USNano
-
Sitecom WL-349 v1
-
Sitecom WL-353
-
Sweex LW154
-
TRENDnet TEW-646UBH
-
TRENDnet TEW-648UB
-
TRENDnet TEW-649UB
Realtek RTL8192C, RTL8188E, RTL8812A and RTL8821A based PCIe IEEE 802.11b/g/n wireless network adapters (MAN.RTWN.4rtwn(4) driver)
The rum(4) driver supports USB 2.0 wireless adapters based on the Ralink RT2501USB and RT2601USB chipsets, including:
-
3Com Aolynk WUB320g
-
Abocom WUG2700
-
Airlink101 AWLL5025
-
ASUS WL-167g ver 2
-
Belkin F5D7050 ver 3
-
Belkin F5D9050 ver 3
-
Buffalo WLI-U2-SG54HP
-
Buffalo WLI-U2-SG54HG
-
Buffalo WLI-U2-G54HP
-
Buffalo WLI-UC-G
-
CNet CWD-854 ver F
-
Conceptronic C54RU ver 2
-
Corega CG-WLUSB2GO
-
D-Link DWA-110
-
D-Link DWA-111
-
D-Link DWL-G122 rev C1
-
D-Link WUA-1340
-
Digitus DN-7003GR
-
Edimax EW-7318USG
-
Gigabyte GN-WB01GS
-
Gigabyte GN-WI05GS
-
Hawking HWUG1
-
Hawking HWU54DM
-
Hercules HWGUSB2-54-LB
-
Hercules HWGUSB2-54V2-AP
-
LevelOne WNC-0301USB v3
-
Linksys WUSB54G rev C
-
Linksys WUSB54GR
-
Planex GW-US54HP
-
Planex GW-US54Mini2
-
Planex GW-USMM
-
Senao NUB-3701
-
Sitecom WL-113 ver 2
-
Sitecom WL-172
-
Sweex LW053
-
TP-LINK TL-WN321G v1/v2/v3
The run(4) driver supports the following wireless adapters:
-
Airlink101 AWLL6090
-
ASUS USB-N11
-
ASUS USB-N13 ver. A1
-
ASUS USB-N66
-
ASUS WL-160N
-
Belkin F5D8051 ver 3000
-
Belkin F5D8053
-
Belkin F5D8055
-
Belkin F6D4050 ver 1
-
Belkin F9L1103
-
Buffalo WLI-UC-AG300N
-
Buffalo WLI-UC-G300HP
-
Buffalo WLI-UC-G300N
-
Buffalo WLI-UC-G301N
-
Buffalo WLI-UC-GN
-
Buffalo WLI-UC-GNM
-
Buffalo WLI-UC-GNM2
-
Corega CG-WLUSB2GNL
-
Corega CG-WLUSB2GNR
-
Corega CG-WLUSB300AGN
-
Corega CG-WLUSB300GNM
-
D-Link DWA-130 rev B1
-
D-Link DWA-140 rev B1, B2, B3, D1
-
D-Link DWA-160 rev B2
-
D-Link DWA-162
-
DrayTek Vigor N61
-
Edimax EW-7711UAn
-
Edimax EW-7711UTn
-
Edimax EW-7717Un
-
Edimax EW-7718Un
-
Edimax EW-7733UnD
-
Gigabyte GN-WB30N
-
Gigabyte GN-WB31N
-
Gigabyte GN-WB32L
-
Hawking HWDN1
-
Hawking HWUN1
-
Hawking HWUN2
-
Hercules HWNU-300
-
Linksys WUSB54GC v3
-
Linksys WUSB600N
-
Logitec LAN-W150N/U2
-
Mvix Nubbin MS-811N
-
Panda Wireless PAU06
-
Planex GW-USMicroN
-
Planex GW-US300MiniS
-
Sitecom WL-182
-
Sitecom WL-188
-
Sitecom WL-301
-
Sitecom WL-302
-
Sitecom WL-315
-
SMC SMCWUSBS-N2
-
Sweex LW303
-
Sweex LW313
-
TP-LINK TL-WDN3200
-
TP-LINK TL-WN321G v4
-
TP-LINK TL-WN727N v3
-
Unex DNUR-81
-
Unex DNUR-82
-
ZyXEL NWD2705
-
ZyXEL NWD210N
-
ZyXEL NWD270N
The uath(4) driver should work with the following adapters:
-
Compex WLU108AG
-
Compex WLU108G
-
D-Link DWL-G132
-
IODATA WN-G54/US
-
MELCO WLI-U2-KAMG54
-
Netgear WG111T
-
Netgear WG111U
-
Netgear WPN111
-
Olitec 000544
-
PLANET WDL-U357
-
Siemens Gigaset 108
-
SMC SMCWUSBT-G
-
SMC SMCWUSBT-G2
-
SparkLAN WL-785A
-
TP-Link TL-WN620G
-
TRENDware International TEW-444UB
-
TRENDware International TEW-504UB
-
Unex Technology UR054ag
-
ZyXEL XtremeMIMO M-202
An up to date list can be found at http://customerproducts.atheros.com/customerproducts/default.asp.
The upgt(4) driver supports USB 2.0 Conexant/Intersil PrismGT series wireless adapters based on the GW3887 chipset, among them:
-
Belkin F5D7050 (version 1000)
-
Cohiba Proto Board
-
D-Link DWL-G120 Cohiba
-
FSC Connect2Air E-5400 USB D1700
-
Gigaset USB Adapter 54
-
Inventel UR045G
-
Netgear WG111v1 (rev2)
-
SMC EZ ConnectG SMC2862W-G
-
Sagem XG703A
-
Spinnaker DUT
-
Spinnaker Proto Board
The ural(4) driver supports USB 2.0 wireless adapters based on the Ralink Technology RT2500USB chipset, including:
-
AMIT WL532U
-
ASUS WL-167g
-
Belkin F5D7050 v2000
-
Buffalo WLI-U2-KG54-AI
-
CNet CWD-854
-
Compex WLU54G 2A1100
-
Conceptronic C54RU
-
D-Link DWL-G122 b1
-
Dynalink WLG25USB
-
E-Tech WGUS02
-
Gigabyte GN-WBKG
-
Hercules HWGUSB2-54
-
KCORP LifeStyle KLS-685
-
Linksys WUSB54G v4
-
Linksys WUSB54GP v4
-
MSI MS-6861
-
MSI MS-6865
-
MSI MS-6869
-
NovaTech NV-902
-
OvisLink Evo-W54USB
-
SerComm UB801R
-
SparkLAN WL-685R
-
Surecom EP-9001-g
-
Sweex LC100060
-
Tonze UW-6200C
-
Zinwell ZWX-G261
-
Zonet ZEW2500P
An up to date list can be found at http://ralink.rapla.net/.
The urtw(4) driver supports Realtek RTL8187B/L based wireless network devices, including:
-
Belkin F5D7050E
-
Linksys WUSB54GCv2
-
Netgear WG111v2
-
Netgear WG111v3
-
Safehome WLG-1500SMA5
-
Shuttle XPC Accessory PN20
-
Sitecom WL168v1
-
Sitecom WL168v4
-
SureCom EP-9001-g(2A)
-
TRENDnet TEW-424UB V3.xR
[i386, amd64] Intel PRO/Wireless 3945ABG MiniPCI network adapters (wpi(4) driver)
The following devices are known to be supported by the zyd(4) driver:
-
3COM 3CRUSB10075
-
Acer WLAN-G-US1
-
Airlink+ AWLL3025
-
Airlink 101 AWLL3026
-
AOpen 802.11g WL54
-
Asus A9T integrated wireless
-
Asus WL-159g
-
Belkin F5D7050 v.4000
-
Billion BiPAC 3011G
-
Buffalo WLI-U2-KG54L
-
CC&C WL-2203B
-
DrayTek Vigor 550
-
Edimax EW-7317UG
-
Edimax EW-7317LDG
-
Fiberline Networks WL-43OU
-
iNexQ UR055g
-
Linksys WUSBF54G
-
Longshine LCS-8131G3
-
MSI US54SE
-
MyTek MWU-201 USB adapter
-
Philips SNU5600
-
Planet WL-U356
-
Planex GW-US54GZ
-
Planex GW-US54GZL
-
Planex GW-US54Mini
-
Safecom SWMULZ-5400
-
Sagem XG 760A
-
Sagem XG 76NA
-
Sandberg Wireless G54 USB
-
Sitecom WL-113
-
SMC SMCWUSB-G
-
Sweex wireless USB 54 Mbps
-
Tekram/Siemens USB adapter
-
Telegent TG54USB
-
Trendnet TEW-424UB rev A
-
Trendnet TEW-429UB
-
TwinMOS G240
-
Unicorn WL-54G
-
US Robotics 5423
-
X-Micro XWL-11GUZX
-
Yakumo QuickWLAN USB
-
Zonet ZEW2501
-
ZyXEL ZyAIR G-202
-
ZyXEL ZyAIR G-220
Miscellaneous Networks
The ce(4) driver supports the following models of Tau-PCI/32 WAN adapters:
-
Cronyx Tau-PCI/32
-
Cronyx Tau-PCI/32-Lite
The cp(4) driver supports the following models of Tau-PCI WAN adapters:
-
Cronyx Tau-PCI
-
Cronyx Tau-PCI/R
-
Cronyx Tau-PCI-L
-
Cronyx Tau-PCI-L/R
-
Cronyx Tau-PCI-E1
-
Cronyx Tau-PCI-G703
-
Cronyx Tau-PCI-2E1
-
Cronyx Tau-PCI-4E1
-
Cronyx Tau-PCI-E3
-
Cronyx Tau-PCI-T3
-
Cronyx Tau-PCI-STS1
Serial Interfaces
The uart(4) driver supports the following classes of UARTs:
-
NS8250: standard hardware based on the 8250, 16450, 16550, 16650, 16750 or the 16950 UARTs.
-
SCC: serial communications controllers supported by the scc(4) device driver.
The scc(4) driver supports the following classes of SCCs:
-
SAB82532: Siemens SAB 82532 based serial communications controllers.
-
Z8530: Zilog 8530 based serial communications controllers.
[amd64, i386] AST 4 port serial card using shared IRQ
-
ARNET 8 port serial card using shared IRQ
-
ARNET (now Digiboard) Sync 570/i high-speed serial
[i386] Boca multi-port serial cards
-
Boca BB1004 4-Port serial card (Modems not supported)
-
Boca IOAT66 6-Port serial card (Modems supported)
-
Boca BB1008 8-Port serial card (Modems not supported)
-
Boca BB2016 16-Port serial card (Modems supported)
[i386] Comtrol Rocketport card (rp(4) driver)
[i386] Cyclades Cyclom-Y serial board (cy(4) driver)
[i386] STB 4 port card using shared IRQ
[amd64, i386] PCI-Based multi-port serial boards (puc(4) driver)
-
[amd64, i386] Actiontech 56K PCI
-
[amd64, i386] Avlab Technology, PCI IO 2S and PCI IO 4S
-
[amd64, i386] Comtrol RocketPort 550
-
[amd64, i386] Decision Computers PCCOM 4-port serial and dual port RS232/422/485
-
[amd64, i386] Dolphin Peripherals 4025/4035/4036
-
[amd64, i386] IC Book Labs Dreadnought 16x Lite and Pro
-
[amd64, i386] Lava Computers 2SP-PCI/DSerial-PCI/Quattro-PCI/Octopus-550
-
[amd64, i386] Middle Digital, Weasle serial port
-
[amd64, i386] Moxa Industio CP-114, Smartio C104H-PCI and C168H/PCI
-
[amd64, i386] NEC PK-UG-X001 and PK-UG-X008
-
[amd64, i386] Netmos NM9835 PCI-2S-550
-
[amd64, i386] Oxford Semiconductor OX16PCI954 PCI UART
-
[amd64, i386] Syba Tech SD-LAB PCI-4S2P-550-ECP
-
[amd64, i386] SIIG Cyber I/O PCI 16C550/16C650/16C850
-
[amd64, i386] SIIG Cyber 2P1S PCI 16C550/16C650/16C850
-
[amd64, i386] SIIG Cyber 2S1P PCI 16C550/16C650/16C850
-
[amd64, i386] SIIG Cyber 4S PCI 16C550/16C650/16C850
-
[amd64, i386] SIIG Cyber Serial (Single and Dual) PCI 16C550/16C650/16C850
-
[amd64, i386] Syba Tech Ltd. PCI-4S2P-550-ECP
-
[amd64, i386] Titan PCI-200H and PCI-800H
-
[amd64, i386] US Robotics (3Com) 3CP5609 modem
-
[amd64, i386] VScom PCI-400 and PCI-800
The rc(4) driver provides support for the SDL Communications RISCom/8 boards.
Sound Devices
The snd_ad1816(4) driver supports the following sound cards:
-
Analog Devices AD1816
The snd_als4000(4) driver supports the following sound cards:
-
Avance Logic ALS4000
The snd_atiixp(4) driver supports the following audio chipsets:
-
ATI IXP 200
-
ATI IXP 300
-
ATI IXP 400
The snd_cmi(4) driver supports the following sound cards:
-
CMedia CMI8338A
-
CMedia CMI8338B
-
CMedia CMI8738
-
CMedia CMI8738B
The snd_cs4281(4) driver supports the following sound cards:
-
Crystal Semiconductor CS4281
The snd_csa(4) driver supports the following sound cards:
-
Crystal Semiconductor CS4280
-
Crystal Semiconductor CS4610
-
Crystal Semiconductor CS4611
-
Crystal Semiconductor CS4614
-
Crystal Semiconductor CS4615
-
Crystal Semiconductor CS4622
-
Crystal Semiconductor CS4624
-
Crystal Semiconductor CS4630
-
Genius Soundmaker 128 Value
-
Hercules Game Theatre XP
-
Turtle Beach Santa Cruz
Some onboard CS4610 chips are accompanied by the CS423x ISA codec instead of the CS4297 AC97 codec. Such configurations are not supported by the snd_csa driver yet.
The snd_ds1(4) driver supports the following sound cards:
-
Yamaha DS-1
-
Yamaha DS-1E
The snd_emu10k1(4) driver supports the following sound cards:
-
Creative SoundBlaster Live! (EMU10K1 Chipset)
-
Creative SoundBlaster Audigy (EMU10K2 Chipset)
-
Creative SoundBlaster Audigy 2 (EMU10K2 Chipset)
-
Creative SoundBlaster Audigy 2 (EMU10K3 Chipset)
The snd_emu10kx(4) driver supports the following sound cards:
-
Creative Sound Blaster Live! (EMU10K1 Chipset). Both PCM and MIDI interfaces are available.
-
Creative Sound Blaster Audigy (CA0100 and CA0101 Chipset). PCM and two MIDI interfaces available.
-
Creative Sound Blaster Audigy 2 and Creative Sound Blaster Audigy 4 (CA0102 Chipset). PCM support is limited to 48kHz/16 bit stereo (192kHz/24 bit part of this chipset is not supported).
-
Creative Sound Blaster Audigy 2 Value (CA0108 Chipset). PCM support is limited to 48kHz/16 bit stereo (192kHz/24 bit part of this chipset is not supported). There is no MIDI support for this card.
The snd_emu10kx(4) driver does not support the following sound cards (although they have names similar to some supported ones):
-
Creative Sound Blaster Live! 24-Bit, identified by FreeBSD as
-
Creative Sound Blaster Audigy LS / ES, identified by FreeBSD as
-
All other Creative sound cards with -DAT chipsets.
-
All Creative X-Fi series sound cards.
The snd_envy24(4) driver supports the following audio devices:
-
M-Audio Audiophile 2496
-
M-Audio Delta Dio 2496
-
Terratec DMX 6fire
Only analog playback is supported. Recording and other features of these cards are not supported.
The snd_envy24ht(4) driver supports the following audio devices:
-
Audiotrak Prodigy 7.1
-
Audiotrak Prodigy 7.1 LT
-
Audiotrak Prodigy 7.1 XT
-
Audiotrak Prodigy HD2
-
ESI Juli@
-
ESI Juli@ XTe
-
M-Audio Audiophile 192
-
M-Audio Revolution 5.1
-
M-Audio Revolution 7.1
-
Terratec Aureon 5.1 Sky
-
Terratec Aureon 7.1 Space
-
Terratec Aureon 7.1 Universe
-
Terratec PHASE 22
-
Terratec PHASE 28
Only analog playback is supported. Recording and other features of these cards are not supported.
The snd_es137x(4) driver supports the following sound cards:
-
Creative CT5880-A
-
Creative CT5880-C
-
Creative CT5880-D
-
Creative CT5880-E
-
Creative SB AudioPCI CT4730
-
Ensoniq AudioPCI ES1370
-
Ensoniq AudioPCI ES1371-A
-
Ensoniq AudioPCI ES1371-B
-
Ensoniq AudioPCI ES1373-A
-
Ensoniq AudioPCI ES1373-B
-
Ensoniq AudioPCI ES1373-8
The snd_ess(4) driver supports the following sound cards:
-
Ensoniq ESS ISA PnP/non-PnP
The snd_fm801(4) driver supports audio devices based on the following chipset:
-
Forte Media FM801
The snd_gusc(4) driver supports the following sound cards:
-
Gravis UltraSound MAX
-
Gravis UltraSound PnP
The snd_hda(4) driver supports controllers having PCI class 4 (multimedia) and subclass 3 (HDA), compatible with Intel HDA specification.
The snd_hda(4) driver supports more than two hundred different controllers and CODECs. There is no sense to list all of them here, as in most cases specific CODEC configuration and wiring are more important then type of the CODEC itself.
The snd_hdspe(4) driver supports the following audio devices:
-
RME HDSPe AIO
-
RME HDSPe RayDAT
The snd_ich(4) driver supports the following audio devices:
-
AMD 768
-
AMD 8111
-
Intel 443MX
-
Intel ICH
-
Intel ICH revision 1
-
Intel ICH2
-
Intel ICH3
-
Intel ICH4
-
Intel ICH5
-
Intel ICH6
-
Intel ICH7
-
NVIDIA nForce
-
NVIDIA nForce2
-
NVIDIA nForce2 400
-
NVIDIA nForce3
-
NVIDIA nForce3 250
-
NVIDIA nForce4
-
SiS 7012
The snd_maestro(4) driver supports the following PCI sound cards:
-
ESS Technology Maestro-1
-
ESS Technology Maestro-2
-
ESS Technology Maestro-2E
The snd_maestro3(4) driver supports the following audio devices:
-
ESS Technology Allegro-1
-
ESS Technology Maestro3
The snd_mss(4) driver supports the following audio devices:
-
AD1845
-
AD1848
-
Aztech 2320
-
CMedia CMI8330
-
Crystal Semiconductor CS4231
-
Crystal Semiconductor CS4232
-
Crystal Semiconductor CS4234
-
Crystal Semiconductor CS4235
-
Crystal Semiconductor CS4236
-
Crystal Semiconductor CS4237
-
ENSONIQ SoundscapeVIVO ENS4081
-
NeoMagic 256AV (non-AC97)
-
OPTi 924
-
OPTi 925
-
OPTi 930
-
OPTi 931
-
OPTi 933
-
Yamaha OPL-SA2
-
Yamaha OPL-SA3
The snd_neomagic(4) driver supports the following audio devices:
-
NeoMagic 256AV
-
NeoMagic 256ZX
The snd_sbc(4) driver supports the following sound cards:
-
Avance Asound 110
-
Avance Logic ALS100+
-
Avance Logic ALS120
-
Creative SB16
-
Creative SB32
-
Creative AWE64
-
Creative AWE64 Gold
-
Creative ViBRA16C
-
Creative ViBRA16X
-
ESS ES1681
-
ESS ES1688
-
ESS ES1868
-
ESS ES1869
-
ESS ES1878
-
ESS ES1879
-
ESS ES1888
The snd_solo(4) driver supports the following sound cards:
-
ESS Solo-1 (ES1938 Chipset)
-
ESS Solo-1E (ES1946 Chipset)
Note that older ESS ISA cards with ES18xx chipset are supported via snd_ess(4) and/or snd_sbc(4) .
The snd_spicds(4) driver supports the following codecs:
-
AK4358
-
AK4381
-
AK4396
-
AK4524
-
AK4528
-
WM8770
The snd_t4dwave(4) driver supports the following audio devices:
-
Acer Labs M5451
-
SIS 7018
-
Trident 4DWave DX
-
Trident 4DWave NX
The snd_via8233(4) driver supports the following audio chipsets:
-
VIA VT8233
-
VIA VT8233A
-
VIA VT8233C
-
VIA VT8235
-
VIA VT8237
-
VIA VT8251
The snd_via82c686(4) driver supports audio devices based on the following chipset:
-
VIA 82C686A
The snd_vibes(4) driver supports audio devices based on the following chipset:
-
S3 SonicVibes
Camera and Video Capture Devices
The bktr(4) driver supports video capture cards based on the Brooktree Bt848/849/878/879 chips, as well as Pinnacle PCTV cards, including:
-
AOpen VA1000
-
AVerMedia AVerTV Studio
-
AVerMedia TF/FM-98
-
ATI TV Wonder VE
-
Hauppauge WinCast/TV
-
Hauppauge WinTV-Go-FM
-
Hauppauge WinTV-pci
-
Hauppauge WinTV-radio
-
Intel Smart Video Recorder III
-
KWORLD PCI TV Tuner
-
Miro PC TV
-
Pinnacle PCTV Pro
-
Pinnacle PCTV Rave
-
PixelView PlayTV PAK
-
PixelView PlayTV Pro (rev 4C, 9D)
-
SIGMA TV II
-
STB TV PCI Television Tuner
-
Super TV Tuner
-
TerraTec TValue
-
V-Stream XPERT TV-PVR 878
-
Video Highway XTreme
-
VideoLogic Captivator PCI
[i386] Connectix QuickCam
USB Devices
[amd64, i386] A range of USB peripherals are supported; devices known to work are listed in this section. Owing to the generic nature of most USB devices, with some exceptions any device of a given class will be supported, even if not explicitly listed here.
Note:
[amd64, i386] USB Ethernet adapters can be found in the section
listing Ethernet interfaces.
Note:
[amd64, i386] USB Bluetooth adapters can be found in Bluetooth section.
The ohci(4) driver supports all OHCI v1.0 compliant controllers including:
-
AcerLabs M5237 (Aladdin-V)
-
AMD-756
-
OPTi 82C861 (FireLink)
-
NEC uPD 9210
-
CMD Tech 670 (USB0670)
-
CMD Tech 673 (USB0673)
-
NVIDIA nForce3
-
Sun PCIO-2 (RIO USB)
The uhci(4) driver supports all UHCI v1.1 compliant controllers including:
-
Intel 82371AB/EB (PIIX4)
-
Intel 82371SB (PIIX3)
-
VIA 83C572
[amd64, i386] USB 2.0 controllers using the EHCI interface (ehci(4) driver)
[amd64, i386] Hubs
[amd64, i386] Keyboards (ukbd(4) driver)
[amd64, i386] Miscellaneous
-
Assist Computer Systems PC Camera C-M1
-
ActiveWire I/O Board
-
Creative Technology Video Blaster WebCam Plus
-
Mirunet AlphaCam Plus
The following devices are supported by the urio(4) driver:
-
Diamond MultiMedia Rio 500
-
Diamond MultiMedia Rio 600
-
Diamond MultiMedia Rio 800
Devices supported by the umodem(4) driver include:
-
3Com 5605
-
Curitel PC5740 Wireless Modem
-
Kyocera AH-K3001V Mobile Phone(WILLCOM)
-
Kyocera WX320K Mobile Phone(WILLCOM)
-
Metricom Ricochet GS USB wireless modem
-
Sierra MC5720 Wireless Modem
-
Yamaha Broadband Wireless Router RTW65b
-
ELSA MicroLink 56k USB modem
-
Sony Ericsson W810i phone
[amd64, i386] Mice (ums(4) driver)
The ulpt(4) driver provides support for USB printers and parallel printer conversion cables, including the following:
-
ATen parallel printer adapter
-
Belkin F5U002 parallel printer adapter
-
Canon BJ F850, S600
-
Canon LBP-1310, 350
-
Entrega USB-to-parallel printer adapter
-
Hewlett-Packard HP Deskjet 3420 (P/N: C8947A #ABJ)
-
Oki Data MICROLINE ML660PS
-
Seiko Epson PM-900C, 880C, 820C, 730C
The ubsa(4) driver supports the following adapters:
-
AnyData ADU-500A EV-DO modem
-
AnyData ADU-E100A (no EV-DO mode support)
-
Belkin F5U103
-
Belkin F5U120
-
e-Tek Labs Kwik232
-
GoHubs GoCOM232
-
Peracom single port serial adapter
The ubser(4) driver provides support for the BWCT console management serial adapters.
The uftdi(4) driver supports the following adapters:
-
B&B Electronics USB→RS422/485 adapter
-
Elexol USB MOD1 and USB MOD3
-
HP USB-Serial adapter shipped with some HP laptops
-
Inland UAS111
-
QVS USC-1000
-
Buffalo PC-OP-RS / Kurouto-shikou KURO-RS universal remote
-
Prologix GPIB-USB Controller
The uplcom(4) driver supports the following devices and adapters:
-
ADLINK ND-6530 USB-Serial Adapter
-
Alcatel One Touch 535/735 Phone
-
Alcor AU9720 USB-RS232 Serial Adapter
-
AlDiga AL-11U Modem
-
Alltronix ACM003U00 Modem
-
Anchor Serial adapter
-
ATEN UC-232A
-
BAFO BF-800 and BF-810
-
Belkin F5U257
-
BenQ S81 Phone
-
Corega CG-USBRS232R Serial Adapter
-
Cressi Edy (Seiko) Diving Computer
-
ELECOM UC-SGT Serial Adapter
-
HAL Corporation Crossam2+USB IR commander
-
Hama USB RS-232 Serial Adapter
-
Hamlet exaggerate XURS232
-
HP LD220 Point-Of-Sale (POS) Display
-
IOGEAR UC-232A
-
I/O DATA USB-RSAQ, USB-RSAQ2, USB-RSAQ3 and USB-RSAQ5
-
iTegno WM1080A GSM/GFPRS Modem
-
iTegno WM2080A CDMA Modem
-
Leadtek 9531 GPS
-
Micromax 610U Modem
-
Microsoft Palm 700WX
-
Mobile Action MA-620 Infrared Adapter
-
Motorola Cables
-
Nokia CA-42 Cable
-
OTI DKU-5 cable
-
Panasonic TY-TP50P6-S flat screen
-
PLX CA-42 Phone Cable
-
PLANEX USB-RS232 URS-03
-
Prolific Generic USB-Serial Adapters
-
Prolific Pharos USB-Serial Adapter
-
RATOC REX-USB60
-
Radio Shack USB Serial Cable
-
Sagem USB-Serial Adapter
-
Samsung I330 Phone Cradle
-
Sandberg USB to Serial Link (model number 133-08)
-
Sanwa KB-USB2 Multimeter cable
-
Siemens/BenQ EF81, SX1, X65 and X75 Mobile Phones
-
Sitecom USB-Serial Adapter
-
SMART Technologies USB-Serial Adapter
-
Sony QN3 Phone Cable
-
Sony Ericsson Datapilot
-
Sony Ericsson DCU-10 and DCU-11 (Susteen) USB Cables
-
SOURCENEXT KeikaiDenwa 8 (with and without charger)
-
Speed Dragon USB-Serial Cable
-
Syntech CPT-8001C Barcode Scanner
-
TDK UHA6400 and UPA9664 USB-PHS Adapters
-
TRENDnet USB to Serial Converter (TU-S9)
-
Tripp-Lite U209-000-R USB-Serial Adapter
-
UIC HCR331 Magnetic Stripe Card Reader
-
UIC MSR206 Magnetic Stripe Card Reader
-
Willcom W-SIM DD PHS terminal.(WS002IN)
-
YC-Cable USB-Serial Adapter
-
Zeagle N2iTion3 Diving Computer
The umct(4) driver supports the following adapters:
-
Belkin F5U109
-
Belkin F5U409
-
D-Link DU-H3SP USB BAY Hub
-
Magic Control Technology USB-232
-
Sitecom USB-232
[amd64, i386] Audio Devices (uaudio(4) driver)
The uvisor(4) driver supports the following devices:
-
Aceeca Mez1000 RDA
-
Handspring Treo
-
Handspring Treo 600
-
Handspring Visor
-
Palm I705
-
Palm M125
-
Palm M130
-
Palm M500
-
Palm M505
-
Palm M515
-
Palm Tungsten T
-
Palm Tungsten Z
-
Palm Zire
-
Palm Zire 31
-
Sony Clie 4.0
-
Sony Clie 4.1
-
Sony Clie 5.0
-
Sony Clie PEG-S500C
-
Sony Clie NX60
-
Sony Clie S360
-
Sony Clie TJ37
IEEE 1394 (Firewire) Devices
The fwohci(4) driver provides support for PCI/CardBus FireWire interface cards. The driver supports the following IEEE 1394 OHCI chipsets:
-
Adaptec AHA-894x/AIC-5800
-
Apple Pangea
-
Apple UniNorth
-
Intel 82372FB
-
IOGEAR GUF320
-
Lucent / Agere FW322/323
-
NEC uPD72861
-
NEC uPD72870
-
NEC uPD72871/2
-
NEC uPD72873
-
NEC uPD72874
-
National Semiconductor CS4210
-
Ricoh R5C551
-
Ricoh R5C552
-
Sony CX3022
-
Sony i.LINK (CXD3222)
-
Sun PCIO-2 (RIO 1394)
-
Texas Instruments PCI4410A
-
Texas Instruments PCI4450
-
Texas Instruments PCI4451
-
Texas Instruments TSB12LV22
-
Texas Instruments TSB12LV23
-
Texas Instruments TSB12LV26
-
Texas Instruments TSB43AA22
-
Texas Instruments TSB43AB21/A/AI/A-EP
-
Texas Instruments TSB43AB22/A
-
Texas Instruments TSB43AB23
-
Texas Instruments TSB82AA2
-
VIA Fire II (VT6306)
[amd64, i386] Serial Bus Protocol 2 (SBP-2) storage devices (sbp(4) driver)
Bluetooth Devices
The ng_bt3c(4) driver provides support for the 3Com/HP 3CRWB6096-A PCCARD bluetooth adapter.
The ng_ubt(4) driver supports all Bluetooth USB devices that conform with the Bluetooth specification v1.1, including:
-
3Com 3CREB96
-
AIPTEK BR0R02
-
EPoX BT-DG02
-
Mitsumi Bluetooth USB adapter
-
MSI MS-6967
-
TDK Bluetooth USB adapter
-
Broadcom Bluetooth USB adapter
Cryptographic Accelerators
The hifn(4) driver supports various cards containing the Hifn 7751, 7951, 7811, 7955, and 7956 chipsets, such as:
-
Invertex AEON
-
Hifn 7751
-
PowerCrypt
-
XL-Crypt
-
NetSec 7751
-
Soekris Engineering vpn1201 and vpn1211
-
Soekris Engineering vpn1401 and vpn1411
The safe(4) driver supports cards containing any of the following chips:
-
SafeNet 1141
-
SafeNet 1741
Miscellaneous
[amd64, i386] FAX-Modem/PCCARD
-
MELCO IGM-PCM56K/IGM-PCM56KH
-
Nokia Card Phone 2.0 (gsm900/dcs1800 HSCSD terminal)
[amd64, i386] Floppy drives (fdc(4) driver)
[amd64, i386] VGA-compatible video cards (vga(4) driver)
Note:
Information regarding specific video cards and compatibility with
Xorg can be found at http://www.x.org/.
[amd64, i386] Keyboards including:
[amd64, i386] Pointing devices including:
Note:
moused(8) has more information on using pointing devices with
FreeBSD. Information on using pointing devices with Xorg can be
found at http://www.x.org/.
[amd64, i386] "PC standard" parallel ports (ppc(4) driver)
[i386] PHS Data Communication Card/PCCARD
-
NTT DoCoMo P-in Comp@ct
-
Panasonic KX-PH405
-
SII MC-P200
[i386] Xilinx XC6200-based reconfigurable hardware cards compatible with the HOT1 from Virtual Computers (xrpu driver).
Last modified on: November 26, 2024 by Alexander Ziaee