FreeBSD Manual Pages
ZONECTL(8) FreeBSD System Manager's Manual ZONECTL(8) NAME zonectl -- Shingled Magnetic Recording Zone Control utility SYNOPSIS zonectl <-d dev> <-c cmd> [-a] [-l LBA] [-o rep_opts] [-P print_opts] DESCRIPTION Manage SCSI and ATA Zoned Block devices. This allows managing devices that conform to the SCSI Zoned Block Commands (ZBC) and ATA Zoned ATA Command Set (ZAC) specifications. Devices using these command sets are usually hard drives using Shingled Magnetic Recording (SMR). There are three types of SMR drives: Drive Managed Drive Managed drives look and act just like a standard random access block device, but underneath, the drive reads and writes the bulk of its capacity using SMR zones. Sequential writes will yield better performance, but writ- ing sequentially is not required. Host Aware Host Aware drives expose the underlying zone layout via SCSI or ATA commands and allow the host to manage the zone conditions. The host is not required to manage the zones on the drive, though. Sequential writes will yield better performance in Sequential Write Preferred zones, but the host can write randomly in those zones. Host Managed Host Managed drives expose the underlying zone layout via SCSI or ATA commands. The host is required to access the zones according to the rules described by the zone layout. Any commands that violate the rules will be returned with an error. SMR drives are divided into zones (typically in the range of 256MB each) that fall into three general categories: Conventional These are also known as Non Write Pointer zones. These zones can be randomly written without an un- expected performance penalty. Sequential Preferred These zones should be written sequentially starting at the write pointer for the zone. They may be written randomly. Writes that do not conform to the zone layout may be significantly slower than expected. Sequential Required These zones must be written sequentially. If they are not written sequentially, starting at the write pointer, the command will fail. -c cmd Specify the zone subcommand: params Display device parameters, including the type of device (Drive Managed, Host Aware, Host Managed, Not Zoned), the zone commands supported, and how many open zones it supports. rz Issue the Report Zones command. All zones are re- turned by default. Specify report options with -o and printing options with -P. Specify the starting LBA with -l. Note that "reportzones" is also ac- cepted as a command argument. open Explicitly open the zone specified by the starting LBA. close Close the zone specified by starting LBA. finish Finish the zone specified by the starting LBA. rwp Reset the write pointer for the zone specified by the starting LBA. -a For the Open, Close, Finish, and Reset Write Pointer opera- tions, apply the operation to all zones on the drive. -l lba Specify the starting LBA. For the Report Zones command, this tells the drive to report starting with the zone that starts at the given LBA. For the other commands, this al- lows the user to identify the zone requested by its start- ing LBA. The LBA may be specified in decimal, hexadecimal or octal notation. -o rep_opt For the Report Zones command, specify a subset of zones to report. all Report all zones. This is the default. emtpy Report only empty zones. imp_open Report zones that are implicitly open. This means that the host has sent a write to the zone without explicitly opening the zone. exp_open Report zones that are explicitly open. closed Report zones that have been closed by the host. full Report zones that are full. ro Report zones that are in the read only state. Note that "readonly" is also accepted as an argu- ment. offline Report zones that are in the offline state. reset Report zones that the device recommends should have their write pointers reset. nonseq Report zones that have the Non Sequential Re- sources Active flag set. These are zones that are Sequential Write Preferred, but have been written non-sequentially. nonwp Report Non Write Pointer zones, also known as Conventional zones. -P print_opt Specify a printing option for Report Zones: normal Normal Report Zones output. This is the default. The summary and column headings are printed, fields are separated by spaces and the fields themselves may contain spaces. summary Just print the summary: the number of zones, the maximum LBA (LBA of the last logical block on the drive), and the value of the "same" field. The "same" field describes whether the zones on the drive are all identical, all different, or whether they are the same except for the last zone, etc. script Print the zones in a script friendly format. The summary and column headings are omitted, the fields are separated by commas, and the fields do not contain spaces. The fields contain under- scores where spaces would normally be used. EXAMPLES zonectl -d /dev/da5 -c params Display basic zoning information for disk da5. zonectl -d /dev/da5 -c rz Issue the Report Zones command to disk da5, and print out all zones on the drive in the default format. zonectl -d /dev/da5 -c rz -o reset -P script Issue the Report Zones command to disk da5, and print out all of the zones that have the Reset Write Pointer Recommended bit set to true. Print the zones in a script friendly form. zonectl -d /dev/da5 -c rwp -l 0x2c80000 Issue the Reset Write Pointer command to disk da5 for the zone that starts at LBA 0x2c80000. SEE ALSO camcontrol(8) AUTHORS Kenneth Merry <ken@FreeBSD.org> FreeBSD 13.0 May 18, 2016 FreeBSD 13.0
NAME | SYNOPSIS | DESCRIPTION | EXAMPLES | SEE ALSO | AUTHORS
Want to link to this manual page? Use this URL:
<https://www.freebsd.org/cgi/man.cgi?query=zonectl&sektion=8&manpath=FreeBSD+13.1-RELEASE+and+Ports>