Skip site navigation (1)Skip section navigation (2)

FreeBSD Man Pages

Man Page or Keyword Search:
Man Architecture
Apropos Keyword Search (all sections) Output format
home | help
UNITS(1)                FreeBSD General Commands Manual               UNITS(1)

NAME
     units - conversion program

SYNOPSIS
     units [-f filename] [-qv] [from-unit to-unit]

OPTIONS
     The following options are available:

     -f filename
             Specify the name of the units data file to load.

     -q      Suppress prompting of the user for units and the display of
             statistics about the number of units loaded.

     -v      Print the version number.

     from-unit to-unit
             Allow a single unit conversion to be done directly from the
             command line.  The program will not print prompts.  It will print
             out the result of the single specified conversion.

DESCRIPTION
     The units program converts quantities expressed in various scales to
     their equivalents in other scales.  The units program can only handle
     multiplicative or affine scale changes.  It works interactively by
     prompting the user for input:

         You have: meters
         You want: feet
                 * 3.2808399
                 / 0.3048

         You have: cm^3
         You want: gallons
                 * 0.00026417205
                 / 3785.4118

         You have: meters/s
         You want: furlongs/fortnight
                 * 6012.8848
                 / 0.00016630952

         You have: 1|2 inch
         You want: cm
                 * 1.27
                 / 0.78740157

         You have: 85 degF
         You want: degC
             29.444444

     Powers of units can be specified using the '^' character as shown in the
     example, or by simple concatenation: 'cm3' is equivalent to 'cm^3'.
     Multiplication of units can be specified by using spaces, a dash or an
     asterisk.  Division of units is indicated by the slash ('/').  Note that
     multiplication has a higher precedence than division, so 'm/s/s' is the
     same as 'm/s^2' or 'm/s s'.  Division of numbers must be indicated using
     the vertical bar ('|').  To convert half a meter, you would write '1|2
     meter'.  If you write '1/2 meter' then the units program would interpret
     that as equivalent to '0.5/meter'.  If you enter incompatible unit types,
     the units program will print a message indicating that the units are not
     conformable and it will display the reduced form for each unit:

         You have: ergs/hour
         You want: fathoms kg^2 / day
         conformability error
                 2.7777778e-11 kg m^2 / sec^3
                 2.1166667e-05 kg^2 m / sec

     The conversion information is read from a units data file.  The default
     file includes definitions for most familiar units, abbreviations and
     metric prefixes.  Some constants of nature included are:

           pi         ratio of circumference to diameter

           c          speed of light

           e          charge on an electron

           g          acceleration of gravity

           force      same as g
           mole       Avogadro's number

           water      pressure per unit height of water

           mercury    pressure per unit height of mercury

           au         astronomical unit

     The unit 'pound' is a unit of mass.  Compound names are run together so
     'pound force' is a unit of force.  The unit 'ounce' is also a unit of
     mass.  The fluid ounce is 'floz'.  British units that differ from their
     US counterparts are prefixed with 'br', and currency is prefixed with its
     country name: 'belgiumfranc', 'britainpound'.  When searching for a unit,
     if the specified string does not appear exactly as a unit name, then
     units will try to remove a trailing 's' or a trailing 'es' and check
     again for a match.

     To find out what units are available read the standard units file.  If
     you want to add your own units you can supply your own file.  A unit is
     specified on a single line by giving its name and an equivalence.  Be
     careful to define new units in terms of old ones so that a reduction
     leads to the primitive units which are marked with '!' characters.  The
     units program will not detect infinite loops that could be caused by
     careless unit definitions.  Comments in the unit definition file begin
     with a '/' character at the beginning of a line.

     Prefixes are defined in the same was as standard units, but with a
     trailing dash at the end of the prefix name.  If a unit is not found even
     after removing trailing 's' or 'es', then it will be checked against the
     list of prefixes.  Prefixes will be removed until a legal base unit is
     identified.

     Here is an example of a short units file that defines some basic units.

           m         !a!
           sec       !b!
           micro-    1e-6
           minute    60 sec
           hour      60 min
           inch      0.0254 m
           ft        12 inches
           mile      5280 ft

FILES
     /usr/share/misc/units.lib  the standard units library

AUTHORS
     Adrian Mariano <adrian@cam.cornell.edu>

BUGS
     The effect of including a '/' in a prefix is surprising.

     Exponents entered by the user can be only one digit.  You can work around
     this by multiplying several terms.

     The user must use | to indicate division of numbers and / to indicate
     division of symbols.  This distinction should not be necessary.

     The program contains various arbitrary limits on the length of the units
     converted and on the length of the data file.

     The program should use a hash table to store units so that it does not
     take so long to load the units list and check for duplication.

FreeBSD 11.0-PRERELEASE          July 14, 1993         FreeBSD 11.0-PRERELEASE

NAME | SYNOPSIS | OPTIONS | DESCRIPTION | FILES | AUTHORS | BUGS

Want to link to this manual page? Use this URL:
<https://www.freebsd.org/cgi/man.cgi?query=units&sektion=1&manpath=FreeBSD+9.2-RELEASE>

home | help