Skip site navigation (1)Skip section navigation (2)

FreeBSD Manual Pages

  
 
  

home | help
ttyadm(1M)		System Administration Commands		    ttyadm(1M)

NAME
       ttyadm -	format and output port monitor-specific	information

SYNOPSIS
       /usr/sbin/ttyadm	 [-b]  [-c] [-h] [-I] [-r count] [-i msg] [-m modules]
       [-p prompt] [-t timeout]	[-S y |	n]  [-T	termtype] -d device  -l	ttyla-
       bel -s service

       /usr/sbin/ttyadm	-V

DESCRIPTION
       The  ttyadm  command  is	 an  administrative  command that formats tty-
       mon(1M)-specific	information and	writes it to standard output. The Ser-
       vice Access Facility (SAF) requires each	port monitor to	provide	such a
       command.	Note that the port monitor administrative file is  updated  by
       the Service Access Controller's administrative commands,	sacadm(1M) and
       pmadm(1M). ttyadm provides a means of presenting	formatted  port	 moni-
       tor-specific (ttymon-specific) data to these commands.

OPTIONS
       The following options are supported:

       -b	       Set the ``bi-directional	port'' flag. When this flag is
		       set, the	line can be used in  both  directions.	ttymon
		       will  allow  users to connect to	the service associated
		       with the	port, but if the  port	is  free,  uucico(1M),
		       cu(1C), or ct(1C) can use it for	dialing	out.

       -c	       Set the connect-on-carrier flag for the port. If	the -c
		       flag is set, ttymon will	invoke the  port's  associated
		       service	immediately  when  a connect indication	is re-
		       ceived (that is,	no prompt is printed and no  baud-rate
		       searching is done).

       -d device       device  is the full pathname of the device file for the
		       TTY port.

       -h	       Set the hangup flag for the port. If the	-h flag	is not
		       set,  ttymon will force a hangup	on the line by setting
		       the speed to 0 before setting the speed to the  default
		       or specified value.

       -i message      Specify	the inactive (disabled)	response message. This
		       message will be sent to the TTY port  if	 the  port  is
		       disabled	or the ttymon monitoring the port is disabled.

       -I	       Initialize only.	 If the	-I option is used, ttymon will
		       invoke the service only once.  This can be used to con-
		       figure  a particular device without actually monitoring
		       it, as with software carrier.

       -l ttylabel     Specify which ttylabel in the /etc/ttydefs file to  use
		       as  the	starting  point	 when searching	for the	proper
		       baud rate.

       -m modules      Specify a list of pushable STREAMS modules. The modules
		       will be pushed in the order in which they are specified
		       before the service is invoked. modules must be a	comma-
		       separated  list	of  modules,  with  no white space in-
		       cluded. Any modules currently on	 the  stream  will  be
		       popped before these  modules are	pushed.

       -p prompt       Specify the prompt message, for example,	``login:''.

       -r count	       When  the  -r option is invoked,	ttymon will wait until
		       it receives data	from the port  before  it  displays  a
		       prompt.	If  count  is 0, ttymon	will wait until	it re-
		       ceives any character. If	count is greater than 0,  tty-
		       mon will	wait until count newlines have been received.

       -s service      service	is  the	full pathname of the service to	be in-
		       voked when a connection request is received.  If	 argu-
		       ments  are required, the	command	and its	arguments must
		       be enclosed in double quotes (" ").

       -S y|n	       Set the software	carrier	value.	y will	turn  software
		       carrier on. n will turn software	carrier	off.

       -t timeout      Specify	that ttymon should close a port	if the open on
		       the port	succeeds, and no input	data  is  received  in
		       timeout seconds.

       -T termtype     Set  the	 terminal type.	 The TERM environment variable
		       will be set to termtype.

       -V	       Display	 the   version	 number	  of	the    current
		       /usr/lib/saf/ttymon command.

OUTPUT
       If successful, ttyadm will generate the requested information, write it
       to  standard output, and	exit with a status of 0. If ttyadm is  invoked
       with  an	invalid	number of arguments or invalid arguments, or if	an in-
       complete	option is specified, an	error message will be written to stan-
       dard error and ttymon will exit with a non-zero status.

FILES
       /etc/ttydefs

ATTRIBUTES
       See attributes(5) for descriptions of the following attributes:

       +-----------------------------+-----------------------------+
       |      ATTRIBUTE	TYPE	     |	    ATTRIBUTE VALUE	   |
       +-----------------------------+-----------------------------+
       |Availability		     |SUNWcsu			   |
       +-----------------------------+-----------------------------+

SEE ALSO
       ct(1C),	cu(1C),	 pmadm(1M),  sacadm(1M),  ttymon(1M),  uucico(1M), at-
       tributes(5)

       System Administration Guide: Basic Administration

SunOS 5.10			  14 Sep 1992			    ttyadm(1M)

NAME | SYNOPSIS | DESCRIPTION | OPTIONS | OUTPUT | FILES | ATTRIBUTES | SEE ALSO

Want to link to this manual page? Use this URL:
<https://www.freebsd.org/cgi/man.cgi?query=ttyadm&sektion=1m&manpath=SunOS+5.10>

home | help