Skip site navigation (1)Skip section navigation (2)

FreeBSD Manual Pages


home | help
TAP(4)		       FreeBSD Kernel Interfaces Manual			TAP(4)

     tap -- Ethernet tunnel software network interface

     device tap

     The tap interface is a software loopback mechanism	that can be loosely
     described as the network interface	analog of the pty(4), that is, tap
     does for network interfaces what the pty(4) driver	does for terminals.

     The tap driver, like the pty(4) driver, provides two interfaces: an
     interface like the	usual facility it is simulating	(an Ethernet network
     interface in the case of tap, or a	terminal for pty(4)), and a character-
     special device ``control''	interface.  A client program transfers Ether-
     net frames	to or from the tap ``control'' interface.  The tun(4) inter-
     face provides similar functionality at the	network	layer: a client	will
     transfer IP (by default) packets to or from a tun(4) ``control'' inter-

     The network interfaces are	named ``tap0'',	``tap1'', etc.,	one for	each
     control device that has been opened.  These Ethernet network interfaces
     persist until if_tap.ko module is unloaded, or until removed with "ifcon-
     fig destroy" (see below).

     tap devices are created using interface cloning.  This is done using the
     ``ifconfig	tapN create'' command.	This is	the preferred method of	creat-
     ing tap devices.  The same	method allows removal of interfaces.  For
     this, use the ``ifconfig tapN destroy'' command.

     If	the sysctl(8) variable is non-zero, the tap
     interface permits opens on	the special control device /dev/tap.  When
     this device is opened, tap	will return a handle for the lowest unused tap
     device (use devname(3) to determine which).

     Disabling the legacy devfs	cloning	functionality may break	existing
     applications which	use tap, such as VMware	and ssh(1).  It	therefore
     defaults to being enabled until further notice.

     Control devices (once successfully	opened)	persist	until if_tap.ko	is
     unloaded or the interface is destroyed.

     Each interface supports the usual Ethernet	network	interface ioctl(2)s
     and thus can be used with ifconfig(8) like	any other Ethernet interface.
     When the system chooses to	transmit an Ethernet frame on the network
     interface,	the frame can be read from the control device (it appears as
     ``input'' there); writing an Ethernet frame to the	control	device gener-
     ates an input frame on the	network	interface, as if the (non-existent)
     hardware had just received	it.

     The Ethernet tunnel device, normally /dev/tapN, is	exclusive-open (it
     cannot be opened if it is already open) and is restricted to the super-
     user, unless the sysctl(8)	variable	is non-zero.
     If	the sysctl(8) variable is non-zero, the	tunnel
     device will be marked ``up'' when the control device is opened.  A	read()
     call will return an error (EHOSTDOWN) if the interface is not ``ready''.
     Once the interface	is ready, read() will return an	Ethernet frame if one
     is	available; if not, it will either block	until one is or	return
     EWOULDBLOCK, depending on whether non-blocking I/O	has been enabled.  If
     the frame is longer than is allowed for in	the buffer passed to read(),
     the extra data will be silently dropped.

     A write(2)	call passes an Ethernet	frame in to be ``received'' on the
     pseudo-interface.	Each write() call supplies exactly one frame; the
     frame length is taken from	the amount of data provided to write().
     Writes will not block; if the frame cannot	be accepted for	a transient
     reason (e.g., no buffer space available), it is silently dropped; if the
     reason is not transient (e.g., frame too large), an error is returned.
     The following ioctl(2) calls are supported	(defined in <net/if_tap.h>):

     TAPSIFINFO		  Set network interface	information (line speed	and
			  MTU).	 The type must be the same as returned by
			  TAPGIFINFO or	set to IFT_ETHER else the ioctl(2)
			  call will fail.  The argument	should be a pointer to
			  a struct tapinfo.

     TAPGIFINFO		  Retrieve network interface information (line speed,
			  MTU and type).  The argument should be a pointer to
			  a struct tapinfo.

     TAPSDEBUG		  The argument should be a pointer to an int; this
			  sets the internal debugging variable to that value.
			  What,	if anything, this variable controls is not
			  documented here; see the source code.

     TAPGDEBUG		  The argument should be a pointer to an int; this
			  stores the internal debugging	variable's value into

     TAPGIFNAME		  Retrieve network interface name.  The	argument
			  should be a pointer to a struct ifreq.  The inter-
			  face name will be returned in	the ifr_name field.

     FIONBIO		  Turn non-blocking I/O	for reads off or on, according
			  as the argument int's	value is or is not zero
			  (Writes are always nonblocking).

     FIOASYNC		  Turn asynchronous I/O	for reads (i.e., generation of
			  SIGIO	when data is available to be read) off or on,
			  according as the argument int's value	is or is not

     FIONREAD		  If any frames	are queued to be read, store the size
			  of the first one into	the argument int; otherwise,
			  store	zero.

     TIOCSPGRP		  Set the process group	to receive SIGIO signals, when
			  asynchronous I/O is enabled, to the argument int

     TIOCGPGRP		  Retrieve the process group value for SIGIO signals
			  into the argument int	value.

     SIOCGIFADDR	  Retrieve the Media Access Control (MAC) address of
			  the ``remote'' side.	This command is	used by	the
			  VMware port and expected to be executed on descrip-
			  tor, associated with control device (usually
			  /dev/vmnetN or /dev/tapN).  The buffer, which	is
			  passed as the	argument, is expected to have enough
			  space	to store the MAC address.  At the open time
			  both ``local'' and ``remote''	MAC addresses are the
			  same,	so this	command	could be used to retrieve the
			  ``local'' MAC	address.

     SIOCSIFADDR	  Set the Media	Access Control (MAC) address of	the
			  ``remote'' side.  This command is used by VMware
			  port and expected to be executed on a	descriptor,
			  associated with control device (usually

     The control device	also supports select(2)	for read; selecting for	write
     is	pointless, and always succeeds,	since writes are always	non-blocking.

     On	the last close of the data device, the interface is brought down (as
     if	with ``ifconfig	tapN down'') unless the	device is a VMnet device, or
     has IFF_LINK0 flag	set.  All queued frames	are thrown away.  If the
     interface is up when the data device is not open, output frames are
     thrown away rather	than letting them pile up.

     The tap device can	also be	used with the VMware port as a replacement for
     the old VMnet device driver.  The driver uses the minor number to select
     between tap and vmnet devices.  VMnet minor numbers begin at 0x800000 +
     N;	where N	is a VMnet unit	number.	 In this case the control device is
     expected to be /dev/vmnetN, and the network interface will	be vmnetN.
     Additionally, VMnet devices do not	ifconfig(8) themselves down when the
     control device is closed.	Everything else	is the same.

     In	addition to the	above mentioned	ioctl(2) calls,	there is an additional
     one for the VMware	port.


     inet(4), intro(4),	tun(4)

FreeBSD	Ports 11.2	       November	29, 2017	    FreeBSD Ports 11.2


Want to link to this manual page? Use this URL:

home | help