Skip site navigation (1)Skip section navigation (2)

FreeBSD Manual Pages

  
 
  

home | help
SMP_REP_ROUTE_INFO(8)		   SMP_UTILS		 SMP_REP_ROUTE_INFO(8)

NAME
       smp_rep_route_info - invoke REPORT ROUTE	INFORMATION SMP	function

SYNOPSIS
       smp_rep_route_info  [--help]  [--hex] [--index=IN] [--interface=PARAMS]
       [--multiple] [--num=NUM]	[--phy=ID] [--raw] [--sa=SAS_ADDR] [--verbose]
       [--version] [--zero] SMP_DEVICE[,N]

DESCRIPTION
       Sends  a	 SAS Serial Management Protocol	(SMP) REPORT ROUTE INFORMATION
       function	request	to an SMP target. The SMP target is identified by  the
       SMP_DEVICE  and	the SAS_ADDR. Depending	on the interface, the SAS_ADDR
       may be deduced from the SMP_DEVICE. The mpt interface  uses  SMP_DEVICE
       to  identify  a	HBA  (an SMP initiator)	and needs the additional ,N to
       differentiate between HBAs if there are multiple	present.

       There are two expander route table types: phy-based and expander-based.
       The  expander-based  route table	was introduced in SAS-2	and supersedes
       the phy-based route tables. The REPORT ROUTE  INFORMATION  function  is
       associated  with	 a phy-based route table. The CONFIGURE	ROUTE INFORMA-
       TION function is	provided to manually set up a phy-based	route table.

       Each phy	in a SAS expander that has an associated routing attribute  of
       "table"	has  a	router	table. The number of rows (or entries) in each
       router table is given by	the "expander route indexes" field in the  re-
       sponse of the REPORT GENERAL function.

       When the	--multiple option is given, the	REPORT ROUTE INFORMATION func-
       tion is called multiple times. The index	value increments on each iter-
       ation,  starting	from --index=IN	(default 0). If	--num=NUM is given and
       NUM is greater than zero	then that is the maximum number	of  iterations
       performed.  If  --num=NUM is not	given (or NUM is zero) then iterations
       continue	until there are	4 adjacent disabled route entries (or some er-
       ror is detected).

OPTIONS
       Mandatory  arguments to long options are	mandatory for short options as
       well.

       -h, --help
	      output the usage message then exit.

       -H, --hex
	      output the response (less	the CRC	field) in hexadecimal.

       -i, --index=IN
	      expander route index. IN is a value between 0 and	65535. Default
	      is   0.	 More  precisely  the  maximum	index  value  is  (ex-
	      pander_route_indexes - 1).

       -I, --interface=PARAMS
	      interface	specific parameters. In	this case  "interface"	refers
	      to  the  path through the	operating system to the	SMP initiator.
	      See the smp_utils	man page for more information.

       -m, --multiple
	      call the	REPORT	ROUTE  INFORMATION  function  multiple	times,
	      starting at --index=IN, incrementing the index value on each it-
	      eration for a maximum of --num=NUM iterations. For each  enabled
	      route table entry, one line is output. If	--num=NUM is not given
	      (or NUM is zero) then iterations continue	until 4	adjacent  dis-
	      abled entries are	found (or some error occurs).

       -n, --num=NUM
	      used with	--multiple option to specify the maximum number	of it-
	      erations.

       -p, --phy=ID
	      phy identifier. ID is a value between 0 and 254. Default is 0.

       -r, --raw
	      send the response	(less the CRC field) to	stdout in binary.  All
	      error messages are sent to stderr.

       -s, --sa=SAS_ADDR
	      specifies	 the  SAS  address of the SMP target device. Typically
	      this is an expander. This	 option	 may  not  be  needed  if  the
	      SMP_DEVICE  has the target's SAS address within it. The SAS_ADDR
	      is in decimal but	most SAS addresses are shown  in  hexadecimal.
	      To  give	a  number in hexadecimal either	prefix it with '0x' or
	      put a trailing 'h' on it.

       -v, --verbose
	      increase the verbosity of	 the  output.  Can  be	used  multiple
	      times.

       -V, --version
	      print the	version	string and then	exit.

       -z, --zero
	      zero  the	 Allocated  Response Length field in the request. This
	      option also zeros	the Request Length field in the	request.  This
	      is  required  for	strict SAS-1.1 compliance. However this	option
	      should not be given in SAS-2  and	 later;	 if  it	 is  given  an
	      abridged response	may result.

CONFORMING TO
       The  SMP	 REPORT	 ROUTE	INFORMATION function was introduced in SAS-1 .
       The "Expander change count" field was added in SAS-2 .

AUTHORS
       Written by Douglas Gilbert.

REPORTING BUGS
       Report bugs to <dgilbert	at interlog dot	com>.

COPYRIGHT
       Copyright (C) 2006-2011 Douglas Gilbert
       This software is	distributed under a FreeBSD license. There is NO  war-
       ranty;  not  even  for MERCHANTABILITY or FITNESS FOR A PARTICULAR PUR-
       POSE.

SEE ALSO
       smp_utils, smp_rep_general(smp_utils)

smp_utils-0.96			   May 2011		 SMP_REP_ROUTE_INFO(8)

NAME | SYNOPSIS | DESCRIPTION | OPTIONS | CONFORMING TO | AUTHORS | REPORTING BUGS | COPYRIGHT | SEE ALSO

Want to link to this manual page? Use this URL:
<https://www.freebsd.org/cgi/man.cgi?query=smp_rep_route_info&sektion=8&manpath=FreeBSD+12.1-RELEASE+and+Ports>

home | help