Skip site navigation (1)Skip section navigation (2)

FreeBSD Manual Pages

  
 
  

home | help
SMP_REP_PHY_SATA(8)		   SMP_UTILS		   SMP_REP_PHY_SATA(8)

NAME
       smp_rep_phy_sata	- invoke REPORT	PHY SATA SMP function

SYNOPSIS
       smp_rep_phy_sata	   [--affiliation=AC]	[--help]   [--hex]   [--inter-
       face=PARAMS] [--phy=ID] [--raw] [--sa=SAS_ADDR] [--verbose] [--version]
       [--zero]	SMP_DEVICE[,N]

DESCRIPTION
       Sends  a	 SAS  Serial Management	Protocol (SMP) REPORT PHY SATA request
       function	to an SMP target. The SMP target is identified by the  SMP_DE-
       VICE  and the SAS_ADDR. Depending on the	interface, the SAS_ADDR	may be
       deduced from the	SMP_DEVICE. The	mpt interface uses SMP_DEVICE to iden-
       tify an HBA (an SMP initiator) and needs	the additional ,N to differen-
       tiate between HBAs if there are multiple	present.

       -a, --affiliation=AC
	      where AC is the affiliation context relative identifier that  is
	      placed in	request	(new in	sas2r08). Defaults to 0.

       -h, --help
	      output the usage message then exit.

       -H, --hex
	      output the response (less	the CRC	field) in hexadecimal.

       -I, --interface=PARAMS
	      interface	 specific  parameters. In this case "interface"	refers
	      to the path through the operating	system to the  SMP  initiator.
	      See the smp_utils	man page for more information.

       -p, --phy=ID
	      phy identifier. ID is a value between 0 and 254. Default is 0.

       -r, --raw
	      send  the	response (less the CRC field) to stdout	in binary. All
	      error messages are sent to stderr.

       -s, --sa=SAS_ADDR
	      specifies	the SAS	address	of the SMP  target  device.  Typically
	      this  is	an  expander.  This  option  may  not be needed	if the
	      SMP_DEVICE has the target's SAS address within it. The  SAS_ADDR
	      is  in  decimal but most SAS addresses are shown in hexadecimal.
	      To give a	number in hexadecimal either prefix it	with  '0x'  or
	      put a trailing 'h' on it.

       -v, --verbose
	      increase the verbosity of	the output. Can	be used	multiple times

       -V, --version
	      print the	version	string and then	exit.

       -z, --zero
	      zero  the	 Allocated  Response Length field in the request. This
	      option also zeros	the Request Length field in the	request.  This
	      is  required  for	strict SAS-1.1 compliance. However this	option
	      should not be given in SAS-2  and	 later;	 if  it	 is  given  an
	      abridged response	may result.

EXAMPLES
       See "Examples" section in http://sg.danny.cz/sg/smp_utils.html

CONFORMING TO
       The  SMP	 REPORT	 PHY SATA function was introduced in SAS-1 .  The "Ex-
       pander change count", "STP I_T nexus loss occurred" and	several	 other
       fields were added in SAS-2 .

AUTHORS
       Written by Douglas Gilbert.

REPORTING BUGS
       Report bugs to <dgilbert	at interlog dot	com>.

COPYRIGHT
       Copyright (C) 2006-2011 Douglas Gilbert
       This  software is distributed under a FreeBSD license. There is NO war-
       ranty; not even for MERCHANTABILITY or FITNESS FOR  A  PARTICULAR  PUR-
       POSE.

SEE ALSO
       smp_utils, smp_phy_control(smp_utils)

smp_utils-0.96			   May 2011		   SMP_REP_PHY_SATA(8)

NAME | SYNOPSIS | DESCRIPTION | EXAMPLES | CONFORMING TO | AUTHORS | REPORTING BUGS | COPYRIGHT | SEE ALSO

Want to link to this manual page? Use this URL:
<https://www.freebsd.org/cgi/man.cgi?query=smp_rep_phy_sata&sektion=8&manpath=FreeBSD+13.0-RELEASE+and+Ports>

home | help