Skip site navigation (1)Skip section navigation (2)

FreeBSD Manual Pages

  
 
  

home | help
SMP_REP_BROADCAST(8)		   SMP_UTILS		  SMP_REP_BROADCAST(8)

NAME
       smp_rep_broadcast - invoke REPORT BROADCAST SMP function

SYNOPSIS
       smp_rep_broadcast    [--broadcast=BT]	[--help]   [--hex]   [--inter-
       face=PARAMS] [--raw] [--sa=SAS_ADDR]  [--verbose]  [--version]  SMP_DE-
       VICE[,N]

DESCRIPTION
       Sends  a	SAS Serial Management Protocol (SMP) REPORT BROADCAST function
       request to an SMP target. The SMP target	is identified by  the  SMP_DE-
       VICE  and  the  --sa=SAS_ADDR. Depending	on the interface, the SAS_ADDR
       may be deduced from the SMP_DEVICE. The mpt interface  uses  SMP_DEVICE
       to  identify  a	HBA  (an SMP initiator)	and needs the additional ,N to
       differentiate between HBAs if there are multiple	present.

OPTIONS
       Mandatory arguments to long options are mandatory for short options  as
       well.

       -b, --broadcast=BT
	      BT is the	broadcast type,	an integer in the range	0 (default) to
	      15.  Broadcast (Change) corresponds to 0.	Other known  broadcast
	      types  are  listed  in the NOTES section.	BT may be decimal (de-
	      fault) or	hexadecimal prefixed by	'0x' (or '0X') or with	a  'h'
	      (or 'H') suffix.

       -h, --help
	      output the usage message then exit.

       -H, --hex
	      output the response (less	the CRC	field) in hexadecimal.

       -I, --interface=PARAMS
	      interface	 specific  parameters. In this case "interface"	refers
	      to the path through the operating	system to the  SMP  initiator.
	      See the smp_utils	man page for more information.

       -r, --raw
	      send  the	response (less the CRC field) to stdout	in binary. All
	      error messages are sent to stderr.

       -s, --sa=SAS_ADDR
	      specifies	the SAS	address	of the SMP target device. The mpt  in-
	      terface needs this option	and it will typically be an expander's
	      SAS address. The SAS_ADDR	is in decimal but most	SAS  addresses
	      are  shown  in hexadecimal.  To give a number in hexadecimal ei-
	      ther prefix it with '0x' or put a	trailing 'h' on	it.

       -v, --verbose
	      increase the verbosity of	 the  output.  Can  be	used  multiple
	      times.

       -V, --version
	      print the	version	string and then	exit.

NOTES
       The following is	a list of broadcast types:
       0	Broadcast (Change)
       1	Broadcast (Reserved change 0)
       2	Broadcast (Reserved change 1)
       3	Broadcast (SES)
       4	Broadcast (Expander)
       5	Broadcast (Asynchronous	event)
       6	Broadcast (Reserved 3)
       7	Broadcast (Reserved 4)
       8	Broadcast (Zone	activate)

       The remaining zone types	(9 to 15) may be issued	by the ZONED BROADCAST
       function.

CONFORMING TO
       The SMP REPORT BROADCAST	function was introduced	in SAS-2 .

AUTHORS
       Written by Douglas Gilbert.

REPORTING BUGS
       Report bugs to <dgilbert	at interlog dot	com>.

COPYRIGHT
       Copyright (C) 2011-2012 Douglas Gilbert
       This software is	distributed under a FreeBSD license. There is NO  war-
       ranty;  not  even  for MERCHANTABILITY or FITNESS FOR A PARTICULAR PUR-
       POSE.

SEE ALSO
       smp_utils, smp_zoned_broadcast(smp_utils)

smp_utils-0.98			 February 2012		  SMP_REP_BROADCAST(8)

NAME | SYNOPSIS | DESCRIPTION | OPTIONS | NOTES | CONFORMING TO | AUTHORS | REPORTING BUGS | COPYRIGHT | SEE ALSO

Want to link to this manual page? Use this URL:
<https://www.freebsd.org/cgi/man.cgi?query=smp_rep_broadcast&sektion=8&manpath=FreeBSD+13.0-RELEASE+and+Ports>

home | help