Skip site navigation (1)Skip section navigation (2)

FreeBSD Manual Pages

  
 
  

home | help
SMP_CONF_ROUTE_INFO(8)		   SMP_UTILS		SMP_CONF_ROUTE_INFO(8)

NAME
       smp_conf_route_info - invoke CONFIGURE ROUTE INFORMATION	SMP function

SYNOPSIS
       smp_conf_route_info [--disable] [--expected=EX] [--help]	[--hex]	[--in-
       dex=IN] [--interface=PARAMS] [--phy=ID]	[--raw]	 [--routed=R_SAS_ADDR]
       [--sa=SAS_ADDR] [--verbose] [--version] SMP_DEVICE[,N]

DESCRIPTION
       Sends  a	 SAS Serial Management Protocol	(SMP) CONFIGURE	ROUTE INFORMA-
       TION function request to	an SMP target. The SMP target is identified by
       the  SMP_DEVICE	and the	--sa=SAS_ADDR. Depending on the	interface, the
       SAS_ADDR	may be deduced from the	SMP_DEVICE.  The  mpt  interface  uses
       SMP_DEVICE  to  identify	 a  HBA	(an SMP	initiator) and needs the addi-
       tional ,N to differentiate between HBAs if there	are multiple present.

       There are two expander route table types: phy-based and expander-based.
       The  expander-based  route table	was introduced in SAS-2	and supersedes
       the phy-based route tables. The CONFIGURE ROUTE INFORMATION function is
       associated  with	 a phy-based route table. The REPORT ROUTE INFORMATION
       function	is provided to report phy-based	route table entries.

       Each phy	in a SAS expander that has an associated routing attribute  of
       "table"	has  a	router	table. The number of rows (or entries) in each
       router table is given by	the "expander route indexes" field in the  re-
       sponse of the REPORT GENERAL function.

OPTIONS
       Mandatory  arguments to long options are	mandatory for short options as
       well.

       -d, --disable
	      set the "disable expander	route entry" flag  in  a  row  of  the
	      router  table  associated	 with --phy=ID of the given SMP	target
	      (e.g. an expander).  Within the router table  the	 row  that  is
	      disabled	is  identified	by  the	 expander route	index given by
	      --index=IN.

       -E, --expected=EX
	      set the 'expected	expander change	count' field in	 the  SMP  re-
	      quest.   The  value EX is	from 0 to 65535	inclusive with 0 being
	      the default value. When EX is greater  than  zero	 then  if  the
	      value  doesn't match the expander	change count of	the SMP	target
	      (i.e. the	expander) when the request arrives then	the target ig-
	      nores  the  request  and	sets a function	result of "invalid ex-
	      pander change count" in the response.

       -h, --help
	      output the usage message then exit.

       -H, --hex
	      output the response (less	the CRC	field) in hexadecimal.

       -i, --index=IN
	      expander route index. IN is a value between 0 and	65535. Default
	      is   0.	 More  precisely  the  maximum	index  value  is  (ex-
	      pander_route_indexes - 1).

       -I, --interface=PARAMS
	      interface	specific parameters. In	this case  "interface"	refers
	      to  the  path through the	operating system to the	SMP initiator.
	      See the smp_utils	man page for more information.

       -p, --phy=ID
	      phy identifier. ID is a value between 0 and 254. Default is 0.

       -r, --raw
	      send the response	(less the CRC field) to	stdout in binary.  All
	      error messages are sent to stderr.

       -R, --routed=R_SAS_ADDR
	      specifies	 the SAS address to be placed in a row (given by --in-
	      dex=IN) of the router table associated  with  --phy=ID.  Default
	      value is 0.  The R_SAS_ADDR is in	decimal	but most SAS addresses
	      are given	in hexadecimal.	To give	a number in hexadecimal	either
	      prefix it	with '0x' or put a trailing 'h'	on it.

       -s, --sa=SAS_ADDR
	      specifies	 the  SAS  address of the SMP target device. Typically
	      this is an expander. This	 option	 may  not  be  needed  if  the
	      SMP_DEVICE  has the target's SAS address within it. The SAS_ADDR
	      is in decimal but	most SAS addresses are shown  in  hexadecimal.
	      To  give	a  number in hexadecimal either	prefix it with '0x' or
	      put a trailing 'h' on it.

       -v, --verbose
	      increase the verbosity of	the output. Can	be used	multiple times

       -V, --version
	      print the	version	string and then	exit.

CONFORMING TO
       The SMP CONFIGURE ROUTE INFORMATION function was	introduced in SAS-1  .
       The "Expander change count" field was added in SAS-2 .

AUTHORS
       Written by Douglas Gilbert.

REPORTING BUGS
       Report bugs to <dgilbert	at interlog dot	com>.

COPYRIGHT
       Copyright (C) 2006-2011 Douglas Gilbert
       This  software is distributed under a FreeBSD license. There is NO war-
       ranty; not even for MERCHANTABILITY or FITNESS FOR  A  PARTICULAR  PUR-
       POSE.

SEE ALSO
       smp_utils, smp_rep_general, smp_rep_route_info(smp_utils)

smp_utils-0.96			   May 2011		SMP_CONF_ROUTE_INFO(8)

NAME | SYNOPSIS | DESCRIPTION | OPTIONS | CONFORMING TO | AUTHORS | REPORTING BUGS | COPYRIGHT | SEE ALSO

Want to link to this manual page? Use this URL:
<https://www.freebsd.org/cgi/man.cgi?query=smp_conf_route_info&sektion=8&manpath=FreeBSD+12.1-RELEASE+and+Ports>

home | help