Skip site navigation (1)Skip section navigation (2)

FreeBSD Manual Pages


home | help
SENDFILE(2)		    BSD	System Calls Manual		   SENDFILE(2)

     sendfile -- send a	file to	a socket

     Standard C	Library	(libc, -lc)

     #include <sys/types.h>
     #include <sys/socket.h>
     #include <sys/uio.h>

     sendfile(int fd, int s, off_t offset, size_t nbytes,
	 struct	sf_hdtr	*hdtr, off_t *sbytes, int flags);

     The sendfile() system call	sends a	regular	file specified by descriptor
     fd	out a stream socket specified by descriptor s.

     The offset	argument specifies where to begin in the file.	Should offset
     fall beyond the end of file, the system will return success and report 0
     bytes sent	as described below.  The nbytes	argument specifies how many
     bytes of the file should be sent, with 0 having the special meaning of
     send until	the end	of file	has been reached.

     An	optional header	and/or trailer can be sent before and after the	file
     data by specifying	a pointer to a struct sf_hdtr, which has the following

	   struct sf_hdtr {
		   struct iovec	*headers;  /* pointer to header	iovecs */
		   int hdr_cnt;		   /* number of	header iovecs */
		   struct iovec	*trailers; /* pointer to trailer iovecs	*/
		   int trl_cnt;		   /* number of	trailer	iovecs */

     The headers and trailers pointers,	if non-NULL, point to arrays of	struct
     iovec structures.	See the	writev() system	call for information on	the
     iovec structure.  The number of iovecs in these arrays is specified by
     hdr_cnt and trl_cnt.

     If	non-NULL, the system will write	the total number of bytes sent on the
     socket to the variable pointed to by sbytes.

     The flags argument	is a bitmap of these values:

	   SF_NODISKIO.	 This flag causes any sendfile() call which would
	   block on disk I/O to	instead	return EBUSY.  Busy servers may	bene-
	   fit by transferring requests	that would block to a separate I/O
	   worker thread.

	   SF_MNOWAIT.	Do not wait for	some kernel resource to	become avail-
	   able, in particular,	mbuf and sf_buf.  The flag does	not make the
	   sendfile() syscall truly non-blocking, since	other resources	are
	   still allocated in a	blocking fashion.

	   SF_SYNC.  sendfile sleeps until the network stack no	longer refer-
	   ences the VM	pages of the file, making subsequent modifications to
	   it safe.  Please note that this is not a guarantee that the data
	   has actually	been sent.

     When using	a socket marked	for non-blocking I/O, sendfile() may send
     fewer bytes than requested.  In this case,	the number of bytes success-
     fully written is returned in *sbytes (if specified), and the error	EAGAIN
     is	returned.

     The FreeBSD implementation	of sendfile() is "zero-copy", meaning that it
     has been optimized	so that	copying	of the file data is avoided.

     On	some architectures, this system	call internally	uses a special
     sendfile()	buffer (struct sf_buf) to handle sending file data to the
     client.  If the sending socket is blocking, and there are not enough
     sendfile()	buffers	available, sendfile() will block and report a state of
     "sfbufa".	If the sending socket is non-blocking and there	are not	enough
     sendfile()	buffers	available, the call will block and wait	for the	neces-
     sary buffers to become available before finishing the call.

     The number	of sf_buf's allocated should be	proportional to	the number of
     nmbclusters used to send data to a	client via sendfile().	Tune accord-
     ingly to avoid blocking!  Busy installations that make extensive use of
     sendfile()	may want to increase these values to be	inline with their
     kern.ipc.nmbclusters (see tuning(7) for details).

     The number	of sendfile() buffers available	is determined at boot time by
     either the	kern.ipc.nsfbufs loader.conf(5)	variable or the	NSFBUFS	kernel
     configuration tunable.  The number	of sendfile() buffers scales with
     kern.maxusers.  The kern.ipc.nsfbufsused and kern.ipc.nsfbufspeak read-
     only sysctl(8) variables show current and peak sendfile() buffers usage
     respectively.  These values may also be viewed through netstat -m.

     If	a value	of zero	is reported for	kern.ipc.nsfbufs, your architecture
     does not need to use sendfile() buffers because their task	can be effi-
     ciently performed by the generic virtual memory structures.

     The sendfile() function returns the value 0 if successful;	otherwise the
     value -1 is returned and the global variable errno	is set to indicate the

     [EAGAIN]		The socket is marked for non-blocking I/O and not all
			data was sent due to the socket	buffer being filled.
			If specified, the number of bytes successfully sent
			will be	returned in *sbytes.

     [EBADF]		The fd argument	is not a valid file descriptor.

     [EBADF]		The s argument is not a	valid socket descriptor.

     [EBUSY]		Completing the entire transfer would have required
			disk I/O, so it	was aborted.  Partial data may have
			been sent.  (This error	can only occur when
			SF_NODISKIO is specified.)

     [EFAULT]		An invalid address was specified for an	argument.

     [EINTR]		A signal interrupted sendfile()	before it could	be
			completed.  If specified, the number of	bytes success-
			fully sent will	be returned in *sbytes.

     [EINVAL]		The fd argument	is not a regular file.

     [EINVAL]		The s argument is not a	SOCK_STREAM type socket.

     [EINVAL]		The offset argument is negative.

     [EIO]		An error occurred while	reading	from fd.

     [ENOTCONN]		The s argument points to an unconnected	socket.

     [ENOTSOCK]		The s argument is not a	socket.

     [EOPNOTSUPP]	The file system	for descriptor fd does not support

     [EPIPE]		The socket peer	has closed the connection.

     netstat(1), open(2), send(2), socket(2), writev(2), tuning(7)

     K.	Elmeleegy, A. Chanda, A. L. Cox, and W.	Zwaenepoel, "A Portable	Kernel
     Abstraction for Low-Overhead Ephemeral Mapping Management", The
     Proceedings of the	2005 USENIX Annual Technical Conference, pp 223-236,

     The sendfile() system call	first appeared in FreeBSD 3.0.	This manual
     page first	appeared in FreeBSD 3.1.

     The sendfile() system call	and this manual	page were written by David G.
     Lawrence <>.

BSD				January	7, 2010				   BSD


Want to link to this manual page? Use this URL:

home | help