Skip site navigation (1)Skip section navigation (2)

FreeBSD Man Pages

Man Page or Keyword Search:
Man Architecture
Apropos Keyword Search (all sections) Output format
home | help
RTADVD(8)               FreeBSD System Manager's Manual              RTADVD(8)

NAME
     rtadvd - router advertisement daemon

SYNOPSIS
     rtadvd [-dDfMRs] [-c configfile] interface ...

DESCRIPTION
     rtadvd sends router advertisement packets to the specified interfaces.

     The program will daemonize itself on invocation.  It will then send
     router advertisement packets periodically, as well as in response to
     router solicitation messages sent by end hosts.

     Router advertisements can be configured on a per-interface basis, as
     described in rtadvd.conf(5).

     If there is no configuration file entry for an interface, or if the
     configuration file does not exist altogether, rtadvd sets all the
     parameters to their default values.  In particular, rtadvd reads all the
     interface routes from the routing table and advertises them as on-link
     prefixes.

     rtadvd also watches the routing table.  If an interface direct route is
     added on an advertising interface and no static prefixes are specified by
     the configuration file, rtadvd adds the corresponding prefix to its
     advertising list.

     Similarly, when an interface direct route is deleted, rtadvd will start
     advertising the prefixes with zero valid and preferred lifetimes to help
     the receiving hosts switch to a new prefix when renumbering.  Note,
     however, that the zero valid lifetime cannot invalidate the
     autoconfigured addresses at a receiving host immediately.  According to
     the specification, the host will retain the address for a certain period,
     which will typically be two hours.  The zero lifetimes rather intend to
     make the address deprecated, indicating that a new non-deprecated address
     should be used as the source address of a new connection.  This behavior
     will last for two hours.  Then rtadvd will completely remove the prefix
     from the advertising list, and succeeding advertisements will not contain
     the prefix information.

     Moreover, if the status of an advertising interface changes, rtadvd will
     start or stop sending router advertisements according to the latest
     status.

     The -s option may be used to disable this behavior; rtadvd will not watch
     the routing table and the whole functionality described above will be
     suppressed.

     Basically, hosts MUST NOT send Router Advertisement messages at any time
     (RFC 2461, Section 6.2.3).  However, it would sometimes be useful to
     allow hosts to advertise some parameters such as prefix information and
     link MTU.  Thus, rtadvd can be invoked if router lifetime is explicitly
     set zero on every advertising interface.

     The command line options are:

     -c      Specify an alternate location, configfile, for the configuration
             file.  By default, /etc/rtadvd.conf is used.

     -d      Print debugging information.

     -D      Even more debugging information is printed.

     -f      Foreground mode (useful when debugging).  Log messages will be
             dumped to stderr when this option is specified.

     -M      Specify an interface to join the all-routers site-local multicast
             group.  By default, rtadvd tries to join the first advertising
             interface appearing on the command line.  This option has meaning
             only with the -R option, which enables routing renumbering
             protocol support.

     -R      Accept router renumbering requests.  If you enable it, certain
             IPsec setup is suggested for security reasons.  This option is
             currently disabled, and is ignored by rtadvd with a warning
             message.

     -s      Do not add or delete prefixes dynamically.  Only statically
             configured prefixes, if any, will be advertised.

     Upon receipt of signal SIGUSR1, rtadvd will dump the current internal
     state into /var/run/rtadvd.dump.

     Use SIGTERM to kill rtadvd gracefully.  In this case, rtadvd will
     transmit router advertisement with router lifetime 0 to all the
     interfaces (in accordance with RFC2461 6.2.5).

RETURN VALUES
     The rtadvd program exits 0 on success, and >0 on failures.

FILES
     /etc/rtadvd.conf                  The default configuration file.
     /var/run/rtadvd.pid               contains the pid of the currently
                                       running rtadvd.
     /var/run/rtadvd.dump              The file in which rtadvd dumps its
                                       internal state.

SEE ALSO
     rtadvd.conf(5), rtsol(8)

HISTORY
     The rtadvd command first appeared in the WIDE Hydrangea IPv6 protocol
     stack kit.

BUGS
     There used to be some text that recommended users not to let rtadvd
     advertise Router Advertisement messages on an upstream link to avoid
     undesirable icmp6(4) redirect messages.  However, based on the later
     discussion in the IETF ipng working group, all routers should rather
     advertise the messages regardless of the network topology, in order to
     ensure reachability.

FreeBSD 11.0-PRERELEASE          May 17, 1998          FreeBSD 11.0-PRERELEASE

NAME | SYNOPSIS | DESCRIPTION | RETURN VALUES | FILES | SEE ALSO | HISTORY | BUGS

Want to link to this manual page? Use this URL:
<https://www.freebsd.org/cgi/man.cgi?query=rtadvd&sektion=8&manpath=FreeBSD+5.2.1-RELEASE>

home | help