Skip site navigation (1)Skip section navigation (2)

FreeBSD Manual Pages


home | help
RTADVD(8)		FreeBSD	System Manager's Manual		     RTADVD(8)

     rtadvd -- router advertisement daemon

     rtadvd [-dDfRs] [-c configfile] [-C ctlsock] [-M ifname] [-p pidfile]
	    [interface ...]

     rtadvd sends router advertisement packets to the specified	interfaces.
     If	no interfaces are specified, rtadvd will still run, but	will not
     advertise any routes until	interfaces are added using rtadvctl(8).

     The program will daemonize	itself on invocation.  It will then send
     router advertisement packets periodically,	as well	as in response to
     router solicitation messages sent by end hosts.

     Router advertisements can be configured on	a per-interface	basis, as
     described in rtadvd.conf(5).

     If	there is no configuration file entry for an interface, or if the con-
     figuration	file does not exist altogether,	rtadvd sets all	the parameters
     to	their default values.  In particular, rtadvd reads all the interface
     routes from the routing table and advertises them as on-link prefixes.

     rtadvd also watches the routing table.  If	an interface direct route is
     added on an advertising interface and no static prefixes are specified by
     the configuration file, rtadvd adds the corresponding prefix to its
     advertising list.

     Similarly,	when an	interface direct route is deleted, rtadvd will start
     advertising the prefixes with zero	valid and preferred lifetimes to help
     the receiving hosts switch	to a new prefix	when renumbering.  Note, how-
     ever, that	the zero valid lifetime	cannot invalidate the autoconfigured
     addresses at a receiving host immediately.	 According to the specifica-
     tion, the host will retain	the address for	a certain period, which	will
     typically be two hours.  The zero lifetimes rather	intend to make the
     address deprecated, indicating that a new non-deprecated address should
     be	used as	the source address of a	new connection.	 This behavior will
     last for two hours.  Then rtadvd will completely remove the prefix	from
     the advertising list, and succeeding advertisements will not contain the
     prefix information.

     Moreover, if the status of	an advertising interface changes, rtadvd will
     start or stop sending router advertisements according to the latest sta-

     The -s option may be used to disable this behavior; rtadvd	will not watch
     the routing table and the whole functionality described above will	be

     Basically,	hosts MUST NOT send Router Advertisement messages at any time
     (RFC 4861,	Section	6.2.3).	 However, it would sometimes be	useful to
     allow hosts to advertise some parameters such as prefix information and
     link MTU.	Thus, rtadvd can be invoked if router lifetime is explicitly
     set zero on every advertising interface.

     The command line options are:

     -c	     Specify an	alternate location, configfile,	for the	configuration
	     file.  By default,	/etc/rtadvd.conf is used.

     -C	     Specify an	alternate location for the control socket used by
	     rtadvctl(8).  The default is /var/run/rtadvd.sock.

     -d	     Print debugging information.

     -D	     Even more debugging information is	printed.

     -f	     Foreground	mode (useful when debugging).  Log messages will be
	     dumped to stderr when this	option is specified.

     -M	     Specify an	interface to join the all-routers site-local multicast
	     group.  By	default, rtadvd	tries to join the first	advertising
	     interface appearing on the	command	line.  This option has meaning
	     only with the -R option, which enables routing renumbering	proto-
	     col support.

     -p	     Specify an	alternative file in which to store the process ID.
	     The default is /var/run/

     -R	     Accept router renumbering requests.  If you enable	it, certain
	     IPsec setup is suggested for security reasons.  This option is
	     currently disabled, and is	ignored	by rtadvd with a warning mes-

     -s	     Do	not add	or delete prefixes dynamically.	 Only statically con-
	     figured prefixes, if any, will be advertised.

     Use SIGHUP	to reload the configuration file /etc/rtadvd.conf.  If an
     invalid parameter is found	in the configuration file upon the reload, the
     entry will	be ignored and the old configuration will be used.  When
     parameters	in an existing entry are updated, rtadvd will send Router
     Advertisement messages with the old configuration but zero	router life-
     time to the interface first, and then start to send a new message.

     Use SIGTERM to kill rtadvd	gracefully.  In	this case, rtadvd will trans-
     mit router	advertisement with router lifetime 0 to	all the	interfaces (in
     accordance	with RFC 4861 6.2.5).

     /etc/rtadvd.conf		       The default configuration file.
     /var/run/	       The default process ID file.

     The rtadvd	utility	exits 0	on success, and	>0 if an error occurs.

     rtadvd.conf(5), rtadvctl(8), rtsol(8)

     Thomas Narten, Erik Nordmark, W. A. Simpson, and Hesham Soliman, Neighbor
     Discovery for IP version 6	(IPv6),	RFC 4861.

     Thomas Narten, Erik Nordmark, and W. A. Simpson, Neighbor Discovery for
     IP	version	6 (IPv6), RFC 2461 (obsoleted by RFC 4861).

     Richard Draves, Default Router Preferences	and More-Specific Routes,

     J.	Jeong, S. Park,	L. Beloeil, and	S. Madanapalli,	IPv6 Router
     Advertisement Options for DNS Configuration, RFC 6106.

     The rtadvd	command	first appeared in the WIDE Hydrangea IPv6 protocol
     stack kit.

     There used	to be some text	that recommended users not to let rtadvd
     advertise Router Advertisement messages on	an upstream link to avoid
     undesirable icmp6(4) redirect messages.  However, based on	the later dis-
     cussion in	the IETF ipng working group, all routers should	rather adver-
     tise the messages regardless of the network topology, in order to ensure

FreeBSD	Ports 11.2	       February	25, 2013	    FreeBSD Ports 11.2


Want to link to this manual page? Use this URL:

home | help