Skip site navigation (1)Skip section navigation (2)

FreeBSD Manual Pages


home | help
RAYCONTROL(8)           FreeBSD System Manager's Manual          RAYCONTROL(8)

     raycontrol -- configure Raytheon Raylink/Webgear Aviator devices

     raycontrol -i iface [-o]
     raycontrol -i iface -t tx rate
     raycontrol -i iface -n network name
     raycontrol -i iface -c ap status
     raycontrol -i iface -p port type
     raycontrol -i iface -m mac address
     raycontrol -i iface -d max data length
     raycontrol -i iface -r RTS threshold
     raycontrol -i iface -f hopset
     raycontrol -i iface -P 0|1
     raycontrol -i iface -S max_sleep_duration
     raycontrol -i iface -Z zero signal cache
     raycontrol -i iface -C display signal cache

     The raycontrol utility controls the operation of Raylink/Webgear wireless
     networking devices via the ray(4) driver.  Most of the parameters that
     can be changed relate to the IEEE 802.11 protocol which the card imple-
     ments.  This includes the station name, whether the station is operating
     in ad-hoc or infrastructure mode, and the network name of a service set
     to join - the BSS in ad-hoc mode or ESS if infrastructure mode is
     enabled.  The raycontrol utility can also be used to view the current
     settings of these parameters and to dump out the values of the card's
     statistics counters.

     The iface argument given to raycontrol should be the logical interface
     name associated with the Raylink/Webgear device (ray0, ray1, ...).

     The options are as follows:

     -i iface [-o]
                 Display the current settings of the specified Raylink/Webgear
                 interface.  This retrieves the current card settings from the
                 driver and prints them out.  The results from this command
                 are a snapshot of the card settings.  Using the additional -o
                 flag will cause raycontrol to print out the statistics coun-
                 ters instead of the card settings.

     -i iface -t tx rate
                 Set the transmit rate of the specified interface.  The NICs
                 support a maximum transmit rate of 2Mbps.  The following ta-
                 ble shows the legal transmit rate settings and the corre-
                 sponding transmit speeds:

                       TX rate     NIC speed
                       1           Very Low (0.5Mbps)
                       2           Low (1Mbps)
                       3           Medium (1.5Mbps)
                       4           High (2Mbps)

                 The version 4 firmware may ignore this setting.  Note, that
                 the IEEE 802.11 standard only allows 1Mbps or 2Mbps opera-
                 tion, and that the generally accepted reading of the IEEE
                 802.11 standard is that 2Mbps is only allowed in infrastruc-
                 ture mode.

     -i iface -n network name
                 Set the name of the service set that this station wishes to
                 join.  The network name can be any text string up to 32 char-
                 acters in length.  The default name is the string "NET-
                 WORK_NAME" which should allow the station to connect to the
                 default Webgear ad-hoc network.

     -i iface -p port type
                 Set the port type for a specified interface.  The legal val-
                 ues for port type are 0 (ad-hoc mode) and 1 (infrastructure
                 mode).  In ad-hoc mode, the station can communicate directly
                 with any other stations within direct radio range (provided
                 that they are also operating in ad-hoc mode).  In infrastruc-
                 ture mode, hosts must associate with a service set controlled
                 by an access point, that relays traffic between end stations.
                 The default setting is 0 (ad-hoc mode).

                 When in ad-hoc mode the station will create a BSS with the
                 network name specified by the -n option if it cannot find an
                 existing network of that name on the currently configured
                 hopset (see the -f option).

     -i iface -m mac address
                 Set the station address for the specified interface.  The mac
                 address is specified as a series of six hexadecimal values
                 separated by colons, e.g.: 00:60:1d:12:34:56.  This programs
                 the new address into the card and updates the interface as

     -i iface -d max_data_length
                 Set the maximum transmit frame size for a specified inter-
                 face.  The max data length can be any number from 350 to 2304
                 or -1 to disable fragmentation.  The default is -1.

     -i iface -r RTS threshold
                 Set the RTS/CTS threshold for a given interface.  This con-
                 trols the number of bytes used for the RTS/CTS handshake
                 boundary.  The RTS threshold can be any value between -1 and
                 2047.  The default is -1 (disable).

     -i iface -f hopset
                 Set the radio hopset of a given interface.  The hopset should
                 be specified as a country code as shown in the table below.
                 The hopset varies both the number of RF channels and their
                 frequencies and is dependent on radio regulations specified
                 by regional authorities.

                       Hopset ID     Country
                       1             USA
                       2             Europe
                       3             Japan
                       4             Korea
                       5             Spain
                       6             France
                       7             Israel
                       8             Australia
                       9             Japan Test

                 Whilst the card can be programmed to work with any hopset it
                 makes sense to use the hopset for your own region to avoid
                 interference from and interfering with other users of the RF
                 spectrum (in places like France this is the military).

                 Note that all stations must be set to the same hopset in
                 order to communicate.

     -i iface -P 0|1
                 Enable or disable power management on a given interface.
                 Enabling power management uses an alternating sleep/wake pro-
                 tocol to help conserve power on mobile stations, at the cost
                 of some increased receive latency.  Power management is off
                 by default.

                 Note that power management requires the cooperation of an
                 access point in order to function; it is not functional in
                 ad-hoc mode.  Legal values for this parameter are 0 (off) and
                 1 (on).

     -i iface -S max_sleep_interval
                 Specify the sleep interval to use when power management is
                 enabled.  The max_sleep_interval is specified in millisec-
                 onds.  The default is 100.

     -i iface -Z
                 Clear the signal strength cache maintained internally by the
                 ray(4) driver.

     -i iface -C
                 Display the cached signal strength information maintained by
                 the ray(4) driver.  The driver retains information about sig-
                 nal strength and noise level for packets received from dif-
                 ferent hosts.  For infrastructure networks the cache stores
                 the signal strength of the access point.

                 The driver also uses the cache to pick the best antenna when

     ray(4), ifconfig(8)

     The raycontrol utility first appeared in FreeBSD 4.0.

     The raycontrol utility was written by Duncan Barclay
     <> and based on the wicontrol utility by Bill Paul

     The -m, -P, -S and -Z options aren't implemented yet.  No access point
     was available for testing against.

     Not tested with Version 5 firmware.

     Hopset changing may not work with version 4 firmware.

     The -W option is un-documented on purpose.

FreeBSD 4.10                    March 21, 2000                    FreeBSD 4.10


Want to link to this manual page? Use this URL:

home | help