Skip site navigation (1)Skip section navigation (2)

FreeBSD Man Pages

Man Page or Keyword Search:
Man Architecture
Apropos Keyword Search (all sections) Output format
home | help
RAYCONTROL(8)           FreeBSD System Manager's Manual          RAYCONTROL(8)

NAME
     raycontrol - configure Raytheon Raylink/Webgear Aviator devices

SYNOPSIS
     raycontrol -i iface [-o]
     raycontrol -i iface -t tx rate
     raycontrol -i iface -n network name
     raycontrol -i iface -c ap status
     raycontrol -i iface -p port type
     raycontrol -i iface -m mac address
     raycontrol -i iface -d max data length
     raycontrol -i iface -r RTS threshold
     raycontrol -i iface -f hopset
     raycontrol -i iface -P 0|1
     raycontrol -i iface -S max_sleep_duration
     raycontrol -i iface -Z zero signal cache
     raycontrol -i iface -C display signal cache

DESCRIPTION
     The raycontrol command controls the operation of Raylink/Webgear wireless
     networking devices via the ray(4) driver.  Most of the parameters that
     can be changed relate to the IEEE 802.11 protocol which the card
     implements.  This includes the station name, whether the station is
     operating in ad-hoc or infrastructure mode, and the network name of a
     service set to join - the BSS in ad-hoc mode or ESS if infrastructure
     mode is enabled.  The raycontrol command can also be used to view the
     current settings of these parameters and to dump out the values of the
     card's statistics counters.

     The iface argument given to raycontrol should be the logical interface
     name associated with the Raylink/Webgear device (ray0, ray1, etc...).

OPTIONS
     The options are as follows:

     -i iface [-o]
                 Display the current settings of the specified Raylink/Webgear
                 interface.  This retrieves the current card settings from the
                 driver and prints them out.  The results from this command
                 are a snapshot of the card settings.  Using the additional -o
                 flag will cause raycontrol to print out the statistics
                 counters instead of the card settings.

     -i iface -t tx rate
                 Set the transmit rate of the specified interface.  The NICs
                 support a maximum transmit rate of 2Mbps.  The following
                 table shows the legal transmit rate settings and the
                 corresponding transmit speeds:

                       TX rate     NIC speed
                       1           Very Low (0.5Mbps)
                       2           Low (1Mbps)
                       3           Medium (1.5Mbps)
                       4           High (2Mbps)

                 The version 4 firmware may ignore this setting.  Note, that
                 the IEEE 802.11 standard only allows 1Mbps or 2Mbps
                 operation, and that the generally accepted reading of the
                 IEEE 802.11 standard is that 2Mbps is only allowed in
                 infrastructure mode.

     -i iface -n network name
                 Set the name of the service set that this station wishes to
                 join.  The network name can be any text string up to 32
                 characters in length.  The default name is the string
                 "NETWORK_NAME" which should allow the station to connect to
                 the default Webgear ad-hoc network.

     -i iface -p port type
                 Set the port type for a specified interface.  The legal
                 values for port type are 0 (ad-hoc mode) and 1
                 (infrastructure mode).  In ad-hoc mode, the station can
                 communicate directly with any other stations within direct
                 radio range (provided that they are also operating in ad-hoc
                 mode).  In inrastructure mode, hosts must associate with a
                 service set controlled by an access point, that relays
                 traffic between end stations.  The default setting is 0 (ad-
                 hoc mode).

                 When in ad-hoc mode the station will create a BSS with the
                 network name specified by the -n option if it cannot find an
                 existing network of that name on the currently configured
                 hopset (see the -f option).

     -i iface -m mac address
                 Set the station address for the specified interface.  The mac
                 address is specified as a series of six hexadecimal values
                 separated by colons, e.g.: 00:60:1d:12:34:56.  This programs
                 the new address into the card and updates the interface as
                 well.

     -i iface -d max_data_length
                 Set the maximum transmit frame size for a specified
                 interface.  The max data length can be any number from 350 to
                 2304 or -1 to disable fragmentation.  The default is -1.

     -i iface -r RTS threshold
                 Set the RTS/CTS threshold for a given interface.  This
                 controls the number of bytes used for the RTS/CTS handshake
                 boundary.  The RTS threshold can be any value between -1 and
                 2047.  The default is -1 (disable).

     -i iface -f hopset
                 Set the radio hopset of a given interface.  The hopset should
                 be specified as a country code as shown in the table below.
                 The hopset varies both the number of RF channels and their
                 frequencies and is dependent on radio regulations specified
                 by regional authorities.

                       Hopset ID     Country
                       1             USA
                       2             Europe
                       3             Japan
                       4             Korea
                       5             Spain
                       6             France
                       7             Israel
                       8             Australia
                       9             Japan Test

                 Whilst the card can be programmed to work with any hopset it
                 makes sense to use the hopset for your own region to avoid
                 interference from and interfering with other users of the RF
                 spectrum (in places like France this is the military).

                 Note that all stations must be set to the same hopset in
                 order to communicate.

     -i iface -P 0|1
                 Enable or disable power management on a given interface.
                 Enabling power management uses an alternating sleep/wake
                 protocol to help conserve power on mobile stations, at the
                 cost of some increased receive latency.  Power management is
                 off by default.

                 Note that power management requires the cooperation of an
                 access point in order to function; it is not functional in
                 ad-hoc mode.  Legal values for this parameter are 0 (off) and
                 1 (on).

     -i iface -S max_sleep_interval
                 Specify the sleep interval to use when power management is
                 enabled.  The max_sleep_interval is specified in
                 milliseconds.  The default is 100.

     -i iface -Z
                 Clear the signal strength cache maintained internally by the
                 ray driver.

     -i iface -C
                 Display the cached signal strength information maintained by
                 the ray driver.  The driver retains information about signal
                 strength and noise level for packets received from different
                 hosts.  For infrastructure networks the cache stores the
                 signal strength of the access point.

                 The driver also uses the cache to pick the best antenna when
                 transmitting.

SEE ALSO
     ray(4), ifconfig(8)

HISTORY
     The raycontrol command first appeared in FreeBSD 4.0.

AUTHORS
     The raycontrol command was written by Duncan Barclay
     <dmlb@ragnet.demon.co.uk> and based on the wicontrol command by Bill Paul
     <wpaul@ctr.columbia.edu>.

BUGS
     The -m, -P, -S and -Z options aren't implemented yet.  No access point
     was available for testing against.

     Not tested with Version 5 firmware.

     Hopset changing may not work with version 4 firmware.

     The -W option is un-documented on purpose.

FreeBSD 11.0-PRERELEASE         March 21, 2000         FreeBSD 11.0-PRERELEASE

NAME | SYNOPSIS | DESCRIPTION | OPTIONS | SEE ALSO | HISTORY | AUTHORS | BUGS

Want to link to this manual page? Use this URL:
<https://www.freebsd.org/cgi/man.cgi?query=raycontrol&sektion=8&manpath=FreeBSD+4.7-RELEASE>

home | help