Skip site navigation (1)Skip section navigation (2)

FreeBSD Manual Pages

  
 
  

home | help
PamRubber User Manual(0)			      PamRubber	User Manual(0)

NAME
       pamrubber  - a rubber-sheeting utility that stretches an	image based on
       control points

SYNOPSIS
       pamrubber {-tri | -quad}	[-linear] [-frame] [-randomseed=N]  cp1x  cp1y
       [cp2x  cp2y  [cp3x  cp3y	 [cp4x cp4y]]] cp1x cp1y [cp2x cp2y [cp3x cp3y
       [cp4x cp4y]]] [filename]

       Minimum unique abbreviation of options is acceptable.  You may use dou-
       ble hyphens instead of single hyphen to denote options.

DESCRIPTION
       This program is part of Netpbm(1).

       The  pamrubber  utility	converts a pam image into a new	image with the
       contents	moved around.  The  transformation  is	often  called  "rubber
       sheeting":  you	identify  control  points (CP) on the source image and
       specify new positions for those points in  the  new  image.   pamrubber
       moves  all  the pixels around, stretching and compressing as necessary,
       as if the original image	were on	a sheet	of rubber and  you  pulled  on
       the sheet to make the control points move to their new locations.

       The new image has the same dimensions and format	as the original.

       The transformation can happen in	two very different ways, called	"quad"
       and "tri." With the former, you must specify four control  points  (for
       both  source  and target).  These are the corners of two	quadrilaterals
       that will act as	the coordinate system for both source and  target  im-
       ages.   Consider	 them  as non-orthogonal (0,0),	(0,1), (1,0) and (1,1)
       points.	This transformation comes  close  to  the  one	pamperspective
       does, however that program does other corrections as well.

       When  you  specify less than four control points, the program adds con-
       trol points in the following way.  With three control points, pamrubber
       chooses	the fourth one such that the four points form a	parallelogram.
       With two	points,	pamrubber considers them the  opposite	corners	 of  a
       rectangle.   When  you specify only one control point, pamrubber	uses a
       rectangle from the top left corner of the image to the  single  control
       point.

       In "tri"	mode, pamrubber	conceptually cuts up the source	and target im-
       age into	triangles.  It Transforms within each  corresponding  pair  of
       triangles in a stretching fashion.  It's	like pulling on	the three cor-
       ners of the triangle.  In this mode, each pixel	in  the	 source	 image
       gets mapped to a	position in the	target image. No pixels	are lost.

       When,  in  "tri"	 mode,	you specify only a single control point	in the
       source and target image,	pamrubber creates  four	 triangles  from  this
       point  to  the  four corners of the image. With two points, the program
       creates six triangles from the two endpoints of the line	connecting the
       two  points,  again  to	the  four  corners of the image. Three control
       points is in a way the core of this utility in "tri" mode.  Between the
       three  edges  of	 the central triangle and the four edges of the	image,
       pamrubber constructs another seven triangles.  Four control points  de-
       fine two	central	connected triangles.  In total this results in cutting
       the source and target image up into ten triangles.

       In this case clearly a picture says more	than a thousand	words.	 There
       is a graphical illustration of these various modes at
	www.schaik.com/netpbm/rubber  <http://www.schaik.com/netpbm/rubber>  .
       An example of how to use	this type of rubber sheeting in	cartography is
       in the article
	Visualizing	  the	    Landscape	   of	   Old-Time	 Tokyo
       <http://www.isprs.org/proceedings/XXXVI/5-W1/papers/21.pdf> .

PARAMETERS
       The parameters are control points (cp) in pairs of x and	y.  The	source
       and target image	must have the same number of control points.  The min-
       imum number of values specified here is 4 for a single control point in
       the source and target image.  The maximum is 16 for four	control	points
       in each image.

       filename	is the name of the input file. If you don't specify this, pam-
       rubber reads the	image from Standard Input.

OPTIONS
       -tri | -quad

	      This selects the type of rubber sheeting done.  You must specify
	      exactly one of these options.

       -linear

	      This determines whether pamrubber	uses nearest neighbor interpo-
	      lation or	bilinear interpolation of four source pixels.

       -frame

	      This  option  causes  pamrubber to overlay the target image with
	      the edges	of the quadrilaterals, respectively the	triangles used
	      for the rubber sheeting.	To get the same	overlay	for the	source
	      image, use a pamrubber  transformation  with  identical  control
	      points for source	and target.

       -randomseed=N

	      pamrubber	 randomizes  some of its output.  So that you can pro-
	      duce repeatable results, you can choose the seed of  the	random
	      number  generator	 with  this option.  If	you use	the same input
	      image and	the same random	number generator seed, you should  al-
	      ways  get	the exact same output.	By default, pamrubber uses the
	      time of day as the seed, so you get  slightly  different	output
	      when you run the program twice on	the same input.

	      Before  Netpbm 10.61 (December 2012), this was called -randseed,
	      and that still works.

SEE ALSO
       pam(1) and pamperspective(1)

HISTORY
       pamrubber was new in Netpbm 10.54 (March	2011).

AUTHORS
       Willem van Schaik wrote this program in February	2011  and  contributed
       it to Netpbm.

DOCUMENT SOURCE
       This  manual  page was generated	by the Netpbm tool 'makeman' from HTML
       source.	The master documentation is at

	      http://netpbm.sourceforge.net/doc/pamrubber.html

netpbm documentation		 February 2011	      PamRubber	User Manual(0)

NAME | SYNOPSIS | DESCRIPTION | PARAMETERS | OPTIONS | SEE ALSO | HISTORY | AUTHORS | DOCUMENT SOURCE

Want to link to this manual page? Use this URL:
<https://www.freebsd.org/cgi/man.cgi?query=pamrubber&sektion=1&manpath=FreeBSD+13.0-RELEASE+and+Ports>

home | help