Skip site navigation (1)Skip section navigation (2)

FreeBSD Man Pages

Man Page or Keyword Search:
Man Architecture
Apropos Keyword Search (all sections) Output format
home | help
ISIC(4)                FreeBSD Kernel Interfaces Manual                ISIC(4)

NAME
     isic - isdn4bsd Siemens ISDN Chipset device driver

SYNOPSIS
   FreeBSD (FreeBSD >= 4.0)
     Asuscom ISDNLink 128K (ISA PnP):
     options "ASUSCOM_IPAC"
     device isic0

     AVM A1 or AVM Fritz!Card classic:
     options "AVM_A1"
     device isic0 at isa? port 0x340 irq 5 flags 4

     Dr. Neuhaus Niccy Go@ (PnP):
     options "DRN_NGO"
     device isic0

     ELSA QuickStep 1000pro ISA (PnP):
     options "ELSA_QS1ISA"
     device isic0

     ELSA MicroLink ISDN/PCI (ELSA QuickStep 1000pro PCI):
     options "ELSA_QS1PCI"
     device isic0

     ELSA PCC-16:
     options "ELSA_PCC16"
     device isic0 at isa? port 0x360 irq 10 flags 20

     Sedlbauer Win Speed card (PnP):
     options "SEDLBAUER"
     device isic0

     Siemens I-Surf 2.0 PnP:
     options "SIEMENS_ISURF2"
     device isic0

     Teles S0/8 or Niccy 1008 card:
     options "TEL_S0_8"
     device isic0 at isa? iomem 0xd0000 irq 5 flags 1

     Teles S0/16 or Creatix ISDN-S0 or Niccy 1016 card:
     options "TEL_S0_16"
     device isic0 at isa? port 0xd80 iomem 0xd0000 irq 5 flags 2

     Teles S0/16.3 card:
     options "TEL_S0_16_3"
     device isic0 at isa? port 0xd80 irq 5 flags 3

     Teles S0/16.3 PnP card (PnP) or Creatix ISDN-S0 P&P card (PnP):
     options "TEL_S0_16_3_P"
     device isic0

     USRobotics Sportster ISDN TA internal or Stollmann Tina-pp card:
     options "USR_STI"
     device isic0 at isa? port 0x268 irq 5 flags 7

     Eicon.Diehl DIVA 2.0 and 2.02 ISA PnP card:
     options "EICON_DIVA"
     device isic0

   NetBSD
     On the ISA bus:

     Teles S0/8 or Niccy 1008 card:
     options "TEL_S0_8"
     isic0 at isa? iomem 0xd0000 irq 5

     Teles S0/16 or Creatix ISDN-S0 or Niccy 1016 card:
     options "TEL_S0_16"
     isic0 at isa? port 0xd80 iomem 0xd0000 irq 5

     Teles S0/16.3 card:
     options "TEL_S0_16_3"
     isic0 at isa? port 0xd80 irq 5

     AVM A1 or AVM Fritz card:
     options "AVM_A1"
     isic0 at isa? port 0x340 irq 5

     USRobotics Sportster ISDN TA internal or Stollmann Tina-pp card:
     options "USR_STI"
     isic0 at isa? port 0x268 irq 5

     ITK ix1 micro card:
     options "ITKIX1"
     isic0 at isa? port 0x398 irq 10

     On the ISAPNP bus:

     Teles S0/16.3 PnP card
     options "TEL_S0_16_3_P"
     isic* at isapnp?

     Creatix ISDN-S0 P&P card
     options "CRTX_S0_P"
     isic* at isapnp?

     Dr. Neuhaus Niccy GO@
     options "DRN_NGO"
     isic* at isapnp?

     ELSA QuickStep 1000pro (ISA version):
     options "ELSA_QS1ISA"
     isic* at isapnp?

     Sedlbauer WinSpeed:
     options "SEDLBAUER"
     isic* at isapnp?

     Dynalink IS64PH:
     options "DYNALINK"
     isic* at isapnp?

     Cards on the PCI bus:

     ELSA QuickStep 1000pro (PCI version)
     options "ELSA_QS1PCI"
     isic* at pci?

     Cards on the PCMCIA or PCCARD bus:

     AVM Fritz!Card PCMCIA
     options "AVM_A1_PCMCIA"
     isic* at pcmcia? function ?

     ELSA MicroLink ISDN/MC
     options "ELSA_ISDNMC"
     isic* at pcmcia? function ?

     ELSA MicroLink MC/all
     options "ELSA_MCALL"
     isic* at pcmcia? function ?

     Cards on the Amiga Zorro bus:

     BSC/ITH ISDN Master, ITH ISDN MasterII or VMC ISDN Blaster
     aster* at zbus?
     isic* at aster? port ?

DESCRIPTION
     The isic driver provides D-channel layer 1 supports as specified in ITU
     Recommendation I.430 and layer 1 support for the B-channel.

     The driver supports several 8 and 16bit passive ISDN cards from various
     manufacturers which are all based upon the popular Siemens ISDN chipset
     consisting of the ISDN Subscriber Access Controller ISAC (such as the
     PEB2085 or PSB 2186) and the High-Level Serial Communications Controller
     Extended HSCX (such as the SAB82525 or PSB21525). The newer IPAC chip
     (which integrates an ISAC and a HSCX in one chip, with the added benefit
     of larger FIFO buffers) is also supported.

SUPPORTED CARDS
     Teles S0/8, Dr. Neuhaus Niccy 1008, Creatix ISDN-S0/8

             The required (optional for NetBSD) flag value is 1.

             Notice that this cards must not have a port value in the config
             line.

             Valid interrupts are 2, 3, 4, 5, 6 and 7.

             The i/o ports are memory mapped and the memory start address may
             be in the range 0xA0000 to 0xDF000 and uses 4kB of memory.

     Teles S0/16, Creatix ISDN-S0, Dr. Neuhaus Niccy 1016

             The required (optional under NetBSD) flag value is 2.

             These boards have a jumper which specifies an i/o base address of
             either 0xd80, 0xe80 or 0xf80. The remaining necessary
             configuration values are then programmed at run time by accessing
             this i/o port.

             Valid interrupts are 2, 3, 4, 5, 10, 11, 12 or 15.

             Valid memory start addresses are 0xC0000, 0xC2000, 0xC4000,
             0xC6000, 0xC8000, 0xCA000, 0xCC000, 0xCE000, 0xD0000, 0xD2000,
             0xD4000, 0xD6000, 0xD8000, 0xDA000, 0xDC000 and 0xDE000.

             Notice: Although the Jumpers are labeled 0xd80, 0xe80 or 0xf80,
             they also require i/o space at addresses 0x180, 0x280 or 0x380.

     Teles S0/16.3

             The required (optional under NetBSD) flag value is 3.

             This card is completely i/o mapped and must not have an iomem
             statement in the config line.

             Valid interrupts are 2, 5, 9, 10, 12 or 15.

             Notice: Although the switch positions are labeled 0x180, 0x280
             and 0x380, the card is to be configured at 0xd80, 0xe80 or 0xf80
             respectively!

     AVM A1, AVM Fritz!Card

             The required (optional under NetBSD) flag value is 4.

             These boards have a jumper which specifies an i/o base address of
             either 0x200, 0x240, 0x300 or 0x340.

             Valid interrupt configurations are 3, 4, 5, 6, 7, 10, 11, 12 or
             15.

             Older Versions of the AVM A1 also require setting of an IRQ
             jumper, newer versions of this and the Fritz!Card only have an
             i/o base jumper and the interrupt is setup at runtime by
             reprogramming a register.

             This card is completely i/o mapped and must not have an iomem
             statement in the config line.

     Teles S0/16.3 PnP

             Possible i/o port values are 0x580, 0x500 and 0x680.  Possible
             interrupt configurations are 3, 5, 7, 10, 11 and 12.

             The the card is auto-configured by the PnP kernel subsystem.

     Creatix ISDN-S0 P_P

             Valid i/o port values are 0x120, 0x180 and 0x100.

             Valid interrupt configurations are 3, 5, 7, 10, 11 and 12.

             The card is auto-configured by the PnP kernel subsystem.

     3Com USRobotics Sportster ISDN TA intern and Stollmann Tina pp

             The required (optional for NetBSD) flag value is 7.

             Valid i/o port values are 0x200, 0x208, 0x210, 0x218, 0x220,
             0x228, 0x230, 0x238, 0x240, 0x248, 0x250, 0x258, 0x260, 0x268,
             0x270 and 0x278.

             Valid interrupt configurations are 5, 7, 10, 11, 12, 14, 15.

             Notice: this card has a strange address decoding scheme resulting
             in 64 windows of some bytes length. Anyway, support for this card
             is good because the manufacturer gave out technical docs for this
             card!

     Dr. Neuhaus Niccy Go@

             Valid i/o port values must be in the range 0x200 ... 0x3e0.

             Valid interrupt configurations are 3, 4, 5, 9, 10, 11, 12, 15.

             The card is auto-configured by the PnP kernel subsystem.

     Sedlbauer Win Speed

             Valid i/o port values must be in the range 0x100 ... 0x3f0.
             (alignment 0x8, len 0x8)

             Valid interrupt configurations are 3, 4, 5, 7, 10, 11, 12, 13,
             15.

             The card is auto-configured by the PnP kernel subsystem.

     ELSA QuickStep 1000pro (ISA)

             I/O port in the range 0x160 ... 0x360 (occupies 8 bytes).

             Valid interrupt configurations are 3, 4, 5, 7, 10, 11, 12, 15.

             The card is auto-configured by the PnP kernel subsystem.

     ELSA QuickStep 1000pro-PCI

             The card is auto-configured by the PCI kernel subsystem.

     ITK ix1 micro

             The required (optional under NetBSD) flag value is 18.

             Valid i/o port values must be in the range (<unknown>).

             Valid interrupt configurations are (<unknown>).

     BSC ISDN Master
     ITH ISDN MasterII
     VMC ISDN Blaster

             The card addresses are auto-configured by the Zorro bus kernel
             subsystem.  The ISDN functions of the boards are at known (to the
             driver) relative addresses.

             Note that currently, you have to jumper the card interupt for IPL
             2 instead of IPL 6 (which is used by most AmigaOS software).

             Note that the ITH ISDN MasterII doesn't work in the DraCo Zorro
             bus. This is no NetBSD problem, but general.

CAVEATS
     Note that all of the boards with I/O ports actually use several ranges of
     port addresses; Teles happen to refer to the 0xd80 range in their
     documentation (the board also uses 0x180 etc.), while AVM happen to refer
     to the 0x200 range in their documentation (the board also uses 0x600
     etc.)  The driver matches the manufacturers' description for the purposes
     of configuration, but of course makes use of all the ports in order to
     operate the card.

BUGS
     Since there is no hardware documentation available from several
     manufacturers for their boards, it is likely that there are many, many
     bugs left.

STANDARDS
     CCITT Recommendation I.430

SEE ALSO
     i4bq921(4), i4bq931(4)

AUTHORS
     The isic driver and this manpage were written by Hellmuth Michaelis
     <hm@kts.org>.  It is based on earlier work of Arne Helme, Andrew Gordon
     and Gary Jennejohn.

     The complete porting to and maintenance of NetBSD was done by Martin
     Husemann <martin@rumolt.teuto.de>.

     The NetBSD/Amiga ISDN Blaster/Master/MasterII driver was written by
     Ignatios Souvatzis <is@netbsd.org>.

FreeBSD 11.0-PRERELEASE        January 26, 2001        FreeBSD 11.0-PRERELEASE

NAME | SYNOPSIS | DESCRIPTION | SUPPORTED CARDS | CAVEATS | BUGS | STANDARDS | SEE ALSO | AUTHORS

Want to link to this manual page? Use this URL:
<https://www.freebsd.org/cgi/man.cgi?query=isic&sektion=4&manpath=FreeBSD+4.5-RELEASE>

home | help