Skip site navigation (1)Skip section navigation (2)

FreeBSD Manual Pages

  
 
  

home | help
GLINT(4x)							     GLINT(4x)

NAME
       glint - GLINT/Permedia video driver

SYNOPSIS
       Section "Device"
	 Identifier "devname"
	 Driver	"glint"
	 ...
       EndSection

DESCRIPTION
       glint  is  an Xorg driver for 3Dlabs & Texas Instruments	GLINT/Permedia
       based video cards. The driver is	rather fully accelerated, and provides
       support	for  the  following  framebuffer  depths:  8, 15 (may give bad
       results with FBDev support), 16,	24 (32 bpp  recommended,  24  bpp  has
       problems), 30, and an 8+24 overlay mode.

SUPPORTED HARDWARE
       The  glint  driver supports 3Dlabs (GLINT MX, GLINT 500TX, GLINT	300SX,
       GLINT GAMMA, GLINT DELTA, GLINT GAMMA2, Permedia, Permedia 2,  Permedia
       2v,  Permedia  3,  R3, R4) and Texas Instruments	(Permedia, Permedia 2)
       chips.

CONFIGURATION DETAILS
       Please refer to xorg.conf(5) for	general	configuration  details.	  This
       section only covers configuration details specific to this driver.

       The  driver  auto-detects  the  chipset type, but the following ChipSet
       names may optionally be specified in the	config file "Device"  section,
       and will	override the auto-detection:

	   "ti_pm2",  "ti_pm",	"r4",  "pm3",  "pm2v",	"pm2",	"pm", "300sx",
	   "500tx", "mx", "gamma", "gamma2", "delta"

       The driver will try to auto-detect the amount of	video  memory  present
       for  all	 chips.	  If it's not detected correctly, the actual amount of
       video memory should be specified	with a VideoRam	entry  in  the	config
       file "Device" section.

       Additionally,  you  may	need to	specify	the bus	ID of your card	with a
       BusID entry in the config file "Device" section,	especially with	 FBDev
       support.

       The following driver Options are	supported:

       Option "UseFlatPanel" "boolean"
	      Enable the FlatPanel feature on the Permedia3.  Default: off.

       Option "SWCursor" "boolean"
	      Enable  or  disable  the	SW cursor.  Default: off.  This	option
	      disables the HWCursor option and vice versa.

       Option "NoAccel"	"boolean"
	      Disable  or  enable  acceleration.   Default:  acceleration   is
	      enabled.

       Option "Overlay"
	      Enable  8+24  overlay  mode.   Only appropriate for depth	24, 32
	      bpp.  (Note: This	hasn't been  tested  with  FBDev  support  and
	      probably	won't  work.)	Recognized values are: "8,24", "24,8".
	      Default: off.

       Option "PciRetry" "boolean"
	      Enable or	disable	PCI retries.  (Note: This  doesn't  work  with
	      Permedia2	based cards for	Amigas.)  Default: off.

       Option "ShadowFB" "boolean"
	      Enable  or  disable use of the shadow framebuffer	layer.	(Note:
	      This disables hardware acceleration.)  Default: off.

       Option "UseFBDev" "boolean"
	      Enable or	disable	use of an OS-specific fb interface  (which  is
	      not supported on all OSs).  See fbdevhw(4x) for further informa-
	      tion.  Default: off.

       Option "BlockWrite" "boolean"
	      Enable or	disable	block writes for the various Permedia 2	chips.
	      This  improves acceleration in general, but disables it for some
	      special cases.  Default: off.

       Option "FireGL3000" "boolean"
	      If you have a card of the	same name,  turn  this	on.   Default:
	      off.

       The Permedia 2 xv driver	supports some additional options:

       Option "Device" "string"
	      A	 path to the Permedia 2	kernel driver. This is required	for Xv
	      support.

       Option "InputBuffers" "integer"
	      Sets the number of buffers for incoming data. Minimum of 1,  max
	      of 2.

       Option "InputFramesPerSec" "integer"
	      Expected frames per second for incoming data.

       Option "InputEncoding" "string"
	      The encoding that	input data will	have.

       Option "OutputBuffers" "integer"
	      This  should  probably  set  the	number of buffers for outgoing
	      data. It actually	does nothing.

       Option "OutputFramesPerSec" "integer"
	      Expected frames per second for outgoing data.

       Option "OutputEncoding" "string"
	      The encoding to put output data in.

       SEE ALSO
	      Xorg(1), xorg.conf(5), Xserver(1), X(7)

AUTHORS
       Authors include:	Alan Hourihane,	Dirk Hohndel,  Stefan  Dirsch,	Michel
       DAxnzer,	Sven Luther

X Version 11		    xf86-video-glint 1.2.9		     GLINT(4x)

NAME | SYNOPSIS | DESCRIPTION | SUPPORTED HARDWARE | CONFIGURATION DETAILS | AUTHORS

Want to link to this manual page? Use this URL:
<https://www.freebsd.org/cgi/man.cgi?query=glint&sektion=4&manpath=FreeBSD+12.0-RELEASE+and+Ports>

home | help