Skip site navigation (1)Skip section navigation (2)

FreeBSD Manual Pages

  
 
  

home | help
ebook2cw(1)			 User Manuals			   ebook2cw(1)

NAME
       ebook2cw	- Convert ebooks to Morse code audio files (MP3/OGG)

SYNOPSIS
       ebook2cw	[OPTIONS] [INFILE]

DESCRIPTION
       ebook2cw	ebook2cw is a command line program which converts a plain text
       ebook to	Morse code audio files.	It works on several platforms, includ-
       ing Windows and Linux.

       A  number  of CW	and audio parameters can be changed from their default
       values, by command line switches	or a config file  (see	below).	 These
       are (default values in brackets):

       -w wpm -	CW speed in words per minute [25]

       -e  wpm - Effective CW speed. If	set, the spaces	are sent at this speed
       instead of the character	speed set by -w	("Farnsworth").

       -W x - Extra Word spacing. Similar to -e, but only affects  the	inter-
       word spacing, not the inter-character spacing.

       -f freq - audio frequency in Hz [600]

       -T SINE|0|SAWTOOTH|1|SQUARE|2 - set waveform to sine, sawtooth, square-
       wave. [sine]

       -Q minutes - Increase CW	speed (QRQ) by 1 WpM  in  intervals  of	 `min-
       utes'.  Speed  will  be reset to	the initial value at the start of each
       chapter.	[0]

       -n - Disables resetting the speed when using the	-Q option.

       -p - Disables the paragraph separator (<BT>)

       -R risetime - risetime, in samples [50]

       -F falltime - falltime, samples [50]

       -O - Use	OGG/Vorbis encoder instead of MP3 if compiled with OGG support

       -X - Do not encode, do not generate output files

       -s samplerate - samplerate for the OGG/MP3 file [11025]

       -b bitrate - MP3	bitrate, kbps [16]

       -q quality - MP3	quality, 1 (best) to 9 (worst).	CW still  sounds  very
       good with the worst quality, encoding time is greatly reduced. [5]

       -c chapter separator - Split chapters at	this string. [CHAPTER]

       -d  duration  -	Splits output files after "duration" seconds; finishes
       the current sentence.

       -l wordlimit - Splits output files after	 "wordlimit"  words;  finished
       the current sentence.

       -o outfile-name - Output	filename (chapter number and .mp3/.ogg will be
       appended) [Chapter]

       -a author - Author for the ID3 tag. Use quotes for strings with	spaces
       (e.g. "JW Goethe")

       -t  title  -  Title for the ID3 tag. Use	quotes for strings with	spaces
       (e.g. "Faust II")

       -k comment - Comment for	the ID3	tag. Use quotes	for strings with  spa-
       ces.

       -y year - Year for the ID3 tag.

       -u  -  Switches input encoding format to	UTF-8. Currently supported al-
       phabets include Latin, Greek, Hebrew, Arabic and	Cyrillic.  Default  is
       ISO 8859-1.

       -g file - Guesses the encoding of `file`	(ISO 8859-1 / ASCII or UTF-8).

       -S [ISO|UTF] - Shows a table of all available morse symbols for the ISO
       8859-1 and UTF-8	character sets.	Output in HTML format.

       -N snr -	When this option is used, a noise background is	added  to  the
       file and	the CW signal is scaled	down to	achieve	a SNR (Signal to Noise
       ratio) of "snr" dB.  Possible range of SNR: -10db to 10dB. Make sure to
       enclose the value in quotation marks if it's negative (i.e. -N "-3").

       -B  bandwidth  in Hz - Sets the filter bandwidth	if the -N / SNR	option
       is used.	Available filters are 100Hz, 500Hz, 1kHz and 2.1kHz.

       -C frequency in Hz - Sets the center frequency of the filter if the  -N
       /  SNR option is	used. This should be set to the	frequency of the Morse
       signal; currently implemented center frequencies: 800Hz

TEXT COMMANDS
       CW prosigns can be generated by enclosing arbitrary  letters  in	 angle
       brackets	(e.g. <AR>, <SK>, ...).

       The  tone  frequency  (f),  speed  (w), effective speed (e), volume (v,
       1..100) waveform	(T) and	SNR (N)	can be changed arbitrarily within  the
       text  by	 inserting  commands, starting with a pipe symbol, followed by
       the parameter to	change and the value.

       Example:	|f400 changes the tone frequency to 400Hz,  |w60  changes  the
       speed to	60wpm, |T3 changes the waveform	to squarewave.

CONFIG FILE AND	CHARACTER MAPPINGS
       ebook2cw	 looks for a config file, ebook2cw.conf, in which all settings
       that can	be changed by command line parameters can be set. Any settings
       made in the config file can be overridden by command line arguments.

       Additionally,  two  `map`  files	 can  be  set  in the config file, for
       ISO8859-1 and UTF-8. You	can map	characters in those files to a string,
       which may be useful to replace characters like the exclamation mark (!)
       to a period (.),	which is more common in	CW.

       A set of	example	config and map file and	a description thereof  can  be
       found at	DESTDIR/share/doc/ebook2cw/examples/.

MISC
       ebook2cw	 can  also  be	compiled  to run as a CGI to serve MP3 and OGG
       files on	the fly	for web	applications.

AUTHOR
       Fabian Kurz, DJ1YFK <fabian@fkurz.net>

       http://fkurz.net/ham/ebook2cw.html

SEE ALSO
       morse(1)

Linux				 DECEMBER 2012			   ebook2cw(1)

NAME | SYNOPSIS | DESCRIPTION | TEXT COMMANDS | CONFIG FILE AND CHARACTER MAPPINGS | MISC | AUTHOR | SEE ALSO

Want to link to this manual page? Use this URL:
<https://www.freebsd.org/cgi/man.cgi?query=ebook2cw&sektion=1&manpath=FreeBSD+12.1-RELEASE+and+Ports>

home | help