Skip site navigation (1)Skip section navigation (2)

FreeBSD Man Pages

Man Page or Keyword Search:
Man Architecture
Apropos Keyword Search (all sections) Output format
home | help
DA(4)                  FreeBSD Kernel Interfaces Manual                  DA(4)

NAME
     da - SCSI Direct Access device driver

SYNOPSIS
     device da
     device da1 at scbus0 target 4 unit 0

DESCRIPTION
     The da driver provides support for all SCSI devices of the direct access
     class that are attached to the system through a supported SCSI Host
     Adapter.  The direct access class includes disk, magneto-optical, and
     solid-state devices.

     A SCSI Host adapter must also be separately configured into the system
     before a SCSI direct access device can be configured.

PARTITIONING
     The da driver allows the disk to have two levels of partitioning.  One
     layer, called the ``slice layer'', is used to separate the FreeBSD areas
     of the disk from areas used by other operating systems.  The second layer
     is the native 4.4BSD partitioning scheme, disklabel(5), which is used to
     subdivide the FreeBSD slices into areas for individual filesystems and
     swap spaces.  For more information, see fdisk(8) and disklabel(8),
     respectively.

     If an uninitialized disk is opened, the slice table will be initialized
     with a fictitious FreeBSD slice spanning the entire disk.  Similarly, if
     an uninitialized (or non-FreeBSD) slice is opened, its disklabel will be
     initialized with parameters returned by the drive and a single `c'
     partition encompassing the entire slice.

CACHE EFFECTS
     Many direct access devices are equipped with read and/or write caches.
     Parameters affecting the device's cache are stored in mode page 8, the
     caching control page.  Mode pages can be examined and modified via the
     camcontrol(8) utility.

     The read cache is used to store data from device-initiated read ahead
     operations as well as frequently used data.  The read cache is
     transparent to the user and can be enabled without any adverse effect.
     Most devices with a read cache come from the factory with it enabled.
     The read cache can be disabled by setting the RCD (Read Cache Disable)
     bit in the caching control mode page.

     The write cache can greatly decrease the latency of write operations and
     allows the device to reorganize writes to increase efficiency and
     performance.  This performance gain comes at a price.  Should the device
     lose power while its cache contains uncommitted write operations, these
     writes will be lost.  The effect of a loss of write transactions on a
     file system is non-deterministic and can cause corruption.  Most devices
     age write transactions to limit vulnerability to a few transactions
     recently reported as complete, but it is none-the-less recommended that
     systems with write cache enabled devices reside on an Uninterruptible
     Power Supply (UPS).  The da device driver ensures that the cache and
     media are synchronized upon final close of the device or an unexpected
     shutdown (panic) event.  This ensures that it is safe to disconnect power
     once the operating system has reported that it has halted.  The write
     cache can be enabled by setting the WCE (Write Cache Enable) bit in the
     caching control mode page.

TAGGED QUEUING
     The da device driver will take full advantage of the SCSI feature known
     as tagged queueing.  Tagged queueing allows the device to process
     multiple transactions concurrently, often re-ordering them to reduce the
     number and length of seeks.  To ensure that transactions to distant
     portions of the media, which may be deferred indefinitely by servicing
     requests nearer the current head position, are completed in a timely
     fashion, an ordered tagged transaction is sent every 15 seconds during
     continuous device operation.

BAD BLOCK RECOVERY
     Direct Access devices have the capability of mapping out portions of
     defective media.  Media recovery parameters are located in mode page 1,
     the Read-Write Error Recovery mode page.  The most important media
     remapping features are 'Auto Write Reallocation' and 'Auto Read
     Reallocation' which can be enabled via the AWRE and ARRE bits,
     respectively, of the Read-Write Error Recovery page.  Many devices do not
     ship from the factory with these feature enabled.  Mode pages can be
     examined and modifie via the camcontrol(8) utility.

KERNEL CONFIGURATION
     It is only necessary to explicitly configure one da device; data
     structures are dynamically allocated as disks are found on the SCSI bus.

IOCTLS
     The following ioctl(2) calls apply to SCSI disks as well as to other
     disks.  They are defined in the header file <sys/disklabel.h>.

     DIOCSBAD    Usually used to set up a bad-block mapping system on the
                 disk.  SCSI drives incorporate their own bad-block mapping so
                 this command is not implemented.

     DIOCGDINFO  Read, from the kernel, the in-core copy of the disklabel for
                 the drive.  This may be a fictitious disklabel if the drive
                 has never been initialized, in which case it will contain
                 information read from the SCSI inquiry commands.

     DIOCSDINFO  Give the driver a new disklabel to use.  The driver will not
                 write the new disklabel to the disk.

     DIOCWLABEL  Enable or disable the driver's software write protect of the
                 disklabel on the disk.

     DIOCWDINFO  Give the driver a new disklabel to use.  The driver will
                 write the new disklabel to the disk.

NOTES
     If a device becomes invalidated (media is removed, device becomes
     unresponsive) the disklabel and information held within the kernel about
     the device will be invalidated.  To avoid corruption of a newly inserted
     piece of media or a replacement device, all accesses to the device will
     be discarded until the last file descriptor referencing the old device is
     closed.  During this period, all new open attempts will be rejected.

FILES
     /dev/rdau      raw mode SCSI disk unit u, accessed as an unpartitioned
                    device
     /dev/dausn     block mode SCSI disk unit u, slice n, accessed as an
                    unpartitioned device
     /dev/rdausn    raw mode SCSI disk unit u, slice n, accessed as an
                    unpartitioned device
     /dev/daup      block mode SCSI disk unit u, first FreeBSD slice,
                    partition p
     /dev/rdaup     raw mode SCSI disk unit u, first FreeBSD slice, partition
                    p
     /dev/dausnp    block mode SCSI disk unit u, nth slice, partition p
     /dev/rdausnp   raw mode SCSI disk unit u, nth slice, partition p

DIAGNOSTICS
     None.

SEE ALSO
     ad(4), disklabel(5), disklabel(8), fdisk(8)

HISTORY
     The da driver was written for the CAM SCSI subsystem by Justin T. Gibbs.
     Many ideas were gleaned from the sd device driver written and ported from
     Mach 2.5 by Julian Elischer.  Support for slices was written by Bruce
     Evans.

FreeBSD 11.0-PRERELEASE        October 15, 1998        FreeBSD 11.0-PRERELEASE

NAME | SYNOPSIS | DESCRIPTION | PARTITIONING | CACHE EFFECTS | TAGGED QUEUING | BAD BLOCK RECOVERY | KERNEL CONFIGURATION | IOCTLS | NOTES | FILES | DIAGNOSTICS | SEE ALSO | HISTORY

Want to link to this manual page? Use this URL:
<https://www.freebsd.org/cgi/man.cgi?query=da&sektion=4&manpath=FreeBSD+4.7-RELEASE>

home | help