Skip site navigation (1)Skip section navigation (2)

FreeBSD Manual Pages

  
 
  

home | help
autopush(1M)		System Administration Commands		  autopush(1M)

NAME
       autopush	- configures lists of automatically pushed STREAMS modules

SYNOPSIS
       autopush	-f filename

       autopush	-g -M major -m minor

       autopush	-r -M major -m minor

DESCRIPTION
       The autopush command configures the list	of modules to be automatically
       pushed onto the stream when a device is opened. It can also be used  to
       remove a	previous setting or get	information on a setting.

OPTIONS
       The following options are supported:

       -f filename
	     Sets  up  the autopush configuration for each driver according to
	     the information stored in filename. An autopush file consists  of
	     lines of four or more fields, separated by	spaces as shown	below:

	     major minor last-minor module1 module2 ...	module8

	     The first field is	a string that specifies	the major device name,
	     as	listed in the /kernel/drv directory. The next two  fields  are
	     integers  that specify the	minor device number and	last-minor de-
	     vice number. The fields following represent the names of modules.
	     If	 minor	is -1, then all	minor devices of a major driver	speci-
	     fied by major are configured, and the value for last-minor	is ig-
	     nored.  If	 last-minor  is	 0, then only a	single minor device is
	     configured. To configure a	range of minor devices for a  particu-
	     lar major,	minor must be less than	last-minor.

	     The  remaining  fields  list the names of modules to be automati-
	     cally pushed onto the stream when opened, along with the position
	     of	 an optional anchor. The maximum number	of modules that	can be
	     pushed is eight. The modules are pushed in	 the  order  they  are
	     specified.	The optional special character sequence	[anchor] indi-
	     cates that	a STREAMS anchor should	be placed on the stream	at the
	     module  previously	specified in the list; it is an	error to spec-
	     ify more than one anchor or to have an anchor first in the	list.

	      A	nonzero	exit status indicates that one or more of the lines in
	     the specified file	failed to complete successfully.

       -g    Gets  the current configuration setting of	a particular major and
	     minor device number specified with	the -M and -m options  respec-
	     tively  and  displays the autopush	modules	associated with	it. It
	     will also return the starting minor device	number if the  request
	     corresponds to a setting of a range (as described with the	-f op-
	     tion).

       -m minor
	     Specifies the minor device	number.

       -M major
	     Specifies the major device	number.

       -r    Removes the previous configuration	setting	of the particular  ma-
	     jor  and minor device number specified with the -M	and -m options
	     respectively. If the values of major and minor  correspond	 to  a
	     previously	established setting of a range of minor	devices, where
	     minor matches the first minor device number  in  the  range,  the
	     configuration would be removed for	the entire range.

EXIT STATUS
       The following exit values are returned:

	      0	    Successful completion.

	      non-zero
		    An error occurred.

EXAMPLES
       Example 1: Using	the autopush command.

       The  following  example gets the	current	configuration settings for the
       major and minor device numbers as indicated and displays	 the  autopush
       modules	 associated   with   them  for	the  character-special	device
       /dev/term/a:

       example#	autopush -g -M 29 -m 0
       Major	 Minor	   Lastminor	 Modules
	 29	   0	     1		 ldterm	 ttcompat

FILES
       /etc/iu.ap

ATTRIBUTES
       See attributes(5) for descriptions of the following attributes:

       +-----------------------------+-----------------------------+
       |      ATTRIBUTE	TYPE	     |	    ATTRIBUTE VALUE	   |
       +-----------------------------+-----------------------------+
       |Availability		     |SUNWcsu			   |
       +-----------------------------+-----------------------------+

SEE ALSO
       bdconfig(1M),   ttymon(1M),   attributes(5),    ldterm(7M),    sad(7D),
       streamio(7I), ttcompat(7M)

       STREAMS Programming Guide

SunOS 5.9			  26 Mar 1999			  autopush(1M)

NAME | SYNOPSIS | DESCRIPTION | OPTIONS | EXIT STATUS | EXAMPLES | FILES | ATTRIBUTES | SEE ALSO

Want to link to this manual page? Use this URL:
<https://www.freebsd.org/cgi/man.cgi?query=autopush&sektion=1m&manpath=SunOS+5.9>

home | help