Skip site navigation (1)Skip section navigation (2)

FreeBSD Man Pages

Man Page or Keyword Search:
Man Architecture
Apropos Keyword Search (all sections) Output format
home | help
ATMCONFIG(8)            FreeBSD System Manager's Manual           ATMCONFIG(8)

NAME
     atmconfig - ATM configuration tool

SYNOPSIS
     atmconfig [-htv] [command [sub-command [...]]] [options] [arg ...]

DESCRIPTION
     The atmconfig tool is used to configure the Netgraph ATM network sub-
     system.

     The command line of atmconfig generally consists of common options
     followed by a command string, optionally followed by sub-command strings,
     optional command specific options and command specific arguments.
     Commands and sub-commands as well as command specific options may be
     abbreviated as long as there is only one match possible.

   Common Options
     The following common options change the overall behaviour of atmconfig:

     -h      Print a very short usage info and exit.

     -t      Several show-type commands output a header and then several lines
             of information.  If this option is given, the header is omitted,
             simplifying the parsing of the output.

     -v      Be more verbose.

   Obtaining Help
     The help command has a number of useful sub-commands.

     To get general help use:
           atmconfig help

     To get a list of available commands use:
           atmconfig help commands

     To get a list of available sub-commands use:
           atmconfig help command

     or (if there are deeper levels of sub-commands):
           atmconfig help command sub-command ...

     To get a list of options and arguments for a command use:
           atmconfig help command sub-command ...
     (given that there are no further sub-command levels).

     To get a list of common options use:
           atmconfig help options

   The diag Ss Command
     The diag command allows the inspection of the ATM interfaces on the local
     host and the modification of device parameters.  Sub-commands are: list
     (print a list of interfaces), config (print hardware configuration), phy
     (access PHY chip), stats (print statistics) and vcc (print list of VCCs).

     atmconfig diag list
             This sub-command lists all ATM interfaces in the system.  It
             takes no options or arguments.

     atmconfig diag config [-atm] [-hardware] [device ...]
             This command prints the configuration of ATM interfaces.  If no
             device is given, all devices are listed, otherwise only the
             specified devices.  The option -atm instructs the command to
             print ATM layer configuration parameters like the number of VCI
             and VPI bits, whereas the -hardware option requests card specific
             information like the vendor or the serial number.  If none of the
             options is given, the defaults is to assume -atm.

     atmconfig diag phy print [-numeric] device
             This command prints the PHY registers in a (potential) human
             comprehensible format.  If -numeric is given, the format is hex
             bytes.  Otherwise, textual representation will be printed.

     atmconfig diag phy show [device ...]
             This sub-command prints static information about the PHY device
             used in the ATM card like the type of the PHY and the media.

     atmconfig diag phy set device reg mask val
             This sub-command allows one to change bits in PHY registers.
             This should be used with great care.  The bits of the given PHY
             chip register for which the corresponding bit in mask is one are
             set to the values of the corresponding bits in val.  All register
             bits that have a zero in mask are written back with their
             original value.

     atmconfig diag phy stats [-clear] device
             Print the PHY statistics for the given device.  When the optional
             -clear is given, the statistics are cleared atomically.

     atmconfig diag vcc [-abr] [-channel] [-traffic] [device]
             Retrieve the list of currently active channels on either all or
             the specified interfaces.  For each channel, the following
             information is printed depending on the options (default is
             -channel).

             -abr         Print ABR specific traffic parameters: ICR, TBE,
                          NRM, TRM, ADTF, RIF, RDF, CDF.

             -channel     Print basic information: VPI, VCI, AAL, traffic
                          type, MTU and flags.

             -traffic     Print traffic parameters: PCR, SCR, MBS, MCR.

     atmconfig diag stats device
             Print driver specific statistics.

   The natm Ss Command
     The natm command is used to change natmip(4) routes on the local host.
     The sub-commands for the routing table are: add (to add a new route),
     delete (to delete an existing route) and show (to print the currently
     installed NATM routes).

     atmconfig natm add dest device vpi vci encaps
     atmconfig natm add dest device vpi vci encaps ubr [pcr]
     atmconfig natm add dest device vpi vci encaps cbr pcr
     atmconfig natm add dest device vpi vci encaps vbr pcr scr mbs
     atmconfig natm add dest device vpi vci encaps abr pcr mcr icr tbe nrm trm
             adtf rif rdf cdf
             Add a new route to the routing table.  The destination address
             (the address on the other end of the link) is given in dest.  The
             device, vpi and vci arguments are the name of the ATM device and
             the VPI and VCI values for the link.  The encaps argument may be
             either AAL5 or LLC/SNAP both of which specify AAL5 encapsulation,
             the first one without additional encapsulation, the second one
             with LLC/SNAP headers.  The first two forms of the command add an
             UBR (unspecified bit rate) channel, where the second form allows
             the optional specification of a peak cell rate (PCR).  The third
             form adds a CBR (constant bit rate) channel where a PCR must be
             given.  The fourth form adds a VBR (variable bit rate) channel.
             The arguments are the peak cell rate, the sustainable cell rate
             and the maximum bursts size.  The last form of the command adds
             an ABR (available bit rate) channel.

     atmconfig natm delete dest
     atmconfig natm delete device vpi vci
             This commands deletes an NATM route.  The route may be specified
             either by the destination address or by the device, vpi and vci
             triple.

     atmconfig natm show
             List all NATM routes.

SEE ALSO
     natm(4), natmip(4), atm(8)

AUTHORS
     Hartmut Brandt <harti@FreeBSD.org>

FreeBSD 11.0-PRERELEASE         August 11, 2003        FreeBSD 11.0-PRERELEASE

NAME | SYNOPSIS | DESCRIPTION | SEE ALSO | AUTHORS

Want to link to this manual page? Use this URL:
<https://www.freebsd.org/cgi/man.cgi?query=atmconfig&sektion=8&manpath=FreeBSD+10.3-RELEASE+and+Ports>

home | help