Skip site navigation (1)Skip section navigation (2)

FreeBSD Manual Pages

  
 
  

home | help
amt-howto(7)	       Miscellaneous Information Manual		  amt-howto(7)

NAME
       amt-howto - Intel AMT with linux	mini howto

DESCRIPTION
   What	is AMT and why I should	care?
       AMT stands for "Active Management Technology".  It provides some	remote
       management facilities.  They are	handled	by the hardware	and  firmware,
       thus  they work independant from	the operation system.  Means: It works
       before Linux bootet up to the point where it activated the network  in-
       terface.	  It  works  even when your most recent	test kernel deadlocked
       the machine.  Which makes it quite useful for development machines ...

       Intel AMT is part of the	vPro  Platform.	  Recent  intel-chipset	 based
       business	 machines should have it.  My fairly new Intel SDV machine has
       it too.

   Documentation
       Look here for documentation beyond this mini howto:
       http://www.intel.com/technology/platform-technology/intel-amt/
       Most useful to get started: "Intel AMT Deployment and Reference Guide"

   Very	short AMT enabling instructions.
       Enter BIOS Setup.
	      *	Enable AMT

       Enter ME	(Management Extention) Setup.  Ctrl-P hotkey works for me.
	      *	Login, factory default password	is "admin".
	      *	Change password.  Trivial ones don't work, must	include	upper-
	      and lowercase letters, digits, special characters.
	      *	Enable AMT Managment.

       Reboot, Enter ME	Setup again with AMT enabled.
	      *	Configure AMT (hostname, network config, ...)
	      *	 Use SMB (Small	Business) management mode.  The	other one (En-
	      terprise)	requires Active	Directory Service Infrastructure,  you
	      don't want that, at least	not for	your first steps ...

   Testing AMT
       Take  your  browser, point it to	http://machine:16992/.	If you config-
       ured AMT	to use DHCP (which is the default) the OS and  the  management
       stack share the same IP address.

       You must	do that	from a remote host as the NIC intercepts network pack-
       ets for AMT, thus it doesn't work from the local	machine	as the packets
       never  pass  the	NIC then.  If everything is fine you'll	see a greeting
       page with a button for login.

       You can login now, using	"admin"	as username and	the  password  config-
       ured  during  setup.  You'll see	some pages with	informations about the
       machine.	 You can also change AMT settings here.

   Control Machine
       You might have noticed already while browing the	pages: There is	a "Re-
       mote  Control" page.  You can remotely reset and	powercycle the machine
       there, thus recover the machine after booting a b0rken kernel,  without
       having someone walk over	to the machine and hit the reset button.

   Serial-over-LAN (SOL) console
       AMT  also provides a virtual serial port	which can be accessed via net-
       work.  That gives you a serial console without a	serial	cable  to  an-
       other machine.

       If  you have activated AMT and SOL the linux kernel should see an addi-
       tional serial port, like	this on	my machine:

	 [root@xeni ~]#	dmesg |	grep ttyS2
	 0000:00:03.3: ttyS2 at	I/O 0xe000 (irq	= 169) is a 16550A

       Edit initab, add	a line like this:

	 S2:2345:respawn:/sbin/agetty ttyS2 115200 vt100-nav

       You should add the serial port to /etc/securetty	too so you are able to
       login  as  root.	  Reload  inittab ("init q").  Use amtterm to connect.
       Tap enter.  You should see a login prompt now and be able to login.

       You can also use	that device as console for the linux kernel, using the
       usual  "console=ttyS2,115200"  kernel command line argument, so you see
       the boot	messages (and kernel Oopses, if	any).

       You can tell grub to use	that serial device, so you can pick a  working
       kernel  for the next boot.  Usual commands from the grub	manual,	except
       that you	need "--port=0xe000" instead of	"--unit=0"  due	 to  the  non-
       standard	 I/O port for the serial line (my machine, yours might use an-
       other port, check linux kernel boot messages).

       The magic command for  the  Xen	kernel	is  "com1=115200,8n1,0xe000,0"
       (again,	you  might  have to replace the	I/O port).  The	final '0' dis-
       ables the IRQ, otherwise	the Xen	kernel hangs at	 boot  after  enabling
       interrupts.

   Fun with Xen	and AMT
       The AMT network stack seems to become slightly confused when running on
       a Xen host in DHCP mode.	 Everything works fine as long	as  only  Dom0
       runs.   But if one starts a guest OS (with bridged networking) AMT sud-
       denly changes the IP address to the one the guest aquired via DHCP.

       It is probably a	good idea to assign a separate static  IP  address  to
       AMT  then.  I didn't manage to switch my	machine	from DHCP to static IP
       yet though, the BIOS refuses to accept the settings.  The error message
       doesn't indicate	why.

   More	fun with AMT
       You  might  want	to download the	DTK (Developer Toolkit,	source code is
       available too) and play with it.	 The .exe is a self-extracting rar ar-
       chive  and  can	be  unpacked  on  linux	 using the unrar utility.  The
       Switchbox comes with  a	linux  binary  (additionally  to  the  Windows
       stuff).	The GUI	tools are written in C#.  Trying to make them fly with
       mono didn't work	for me though (mono version 1.2.3 as shipped with  Fe-
       dora 7).

SEE ALSO
       amtterm(1), gamt(1), amttool(1)

       http://www.intel.com/technology/platform-technology/intel-amt/

WRITTEN	BY
       Gerd Hoffmann <kraxel@redhat.com>

			    (c)	2007 Gerd Hoffmann		  amt-howto(7)

NAME | DESCRIPTION | SEE ALSO | WRITTEN BY

Want to link to this manual page? Use this URL:
<https://www.freebsd.org/cgi/man.cgi?query=amt-howto&sektion=7&manpath=FreeBSD+12.0-RELEASE+and+Ports>

home | help