Skip site navigation (1)Skip section navigation (2)

FreeBSD Man Pages

Man Page or Keyword Search:
Man Architecture
Apropos Keyword Search (all sections) Output format
home | help
UPGT(4)		       FreeBSD Kernel Interfaces Manual		       UPGT(4)

NAME
     upgt -- Conexant/Intersil PrismGT SoftMAC USB IEEE	802.11b/g wireless
     network device

SYNOPSIS
     To	compile	this driver into the kernel, place the following lines in your
     kernel configuration file:

	   device ehci
	   device uhci
	   device ohci
	   device usb
	   device upgt
	   device wlan

     Alternatively, to load the	driver as a module at boot time, place the
     following line in loader.conf(5):

	   if_upgt_load="YES"

DESCRIPTION
     The upgt driver supports the USB 2.0 Conexant/Intersil PrismGT series
     wireless adapters based on	the GW3887 chipset.

     These are the modes the upgt driver can operate in:

     BSS mode	    Also known as infrastructure mode, this is used when asso-
		    ciating with an access point, through which	all traffic
		    passes.  This mode is the default.

     monitor mode   In this mode the driver is able to receive packets without
		    associating	with an	access point.  This disables the
		    internal receive filter and	enables	the card to capture
		    packets from networks which	it wouldn't normally have
		    access to, or to scan for access points.

     upgt supports software WEP.  Wired	Equivalent Privacy (WEP) is the	de
     facto encryption standard for wireless networks.  It can be typically
     configured	in one of three	modes: no encryption; 40-bit encryption; or
     104-bit encryption.  Unfortunately, due to	serious	weaknesses in WEP pro-
     tocol it is strongly recommended that it not be used as the sole mecha-
     nism to secure wireless communication.  WEP is not	enabled	by default.

     The upgt driver can be configured at runtime with ifconfig(8).

FILES
     This driver requires the upgtfw firmware to be installed before it	will
     work.  The	firmware files are not publicly	available.  A package of the
     firmware which can	be installed via pkg_add(1) is available:

	   http://weongyo.org/project/upgt/upgt-firmware-2.13.1.0.tar.gz

HARDWARE
     The upgt driver supports USB 2.0 Conexant/Intersil	PrismGT	series wire-
     less adapters based on the	GW3887 chipset,	among them:

     +o	 Belkin	F5D7050	(version 1000)
     +o	 Cohiba	Proto Board
     +o	 D-Link	DWL-G120 Cohiba
     +o	 FSC Connect2Air E-5400	USB D1700
     +o	 Gigaset USB Adapter 54
     +o	 Inventel UR045G
     +o	 SMC EZ	ConnectG SMC2862W-G
     +o	 Sagem XG703A
     +o	 Spinnaker DUT
     +o	 Spinnaker Proto Board

EXAMPLES
     Join an existing BSS network (i.e., connect to an access point):

	   ifconfig wlan create	wlandev	upgt0 inet 192.168.0.20	\
	       netmask 0xffffff00

     Join a specific BSS network with network name ``my_net'':

	   ifconfig wlan create	wlandev	upgt0 ssid my_net up

     Join a specific BSS network with 64-bit WEP encryption:

	   ifconfig wlan create	wlandev	upgt0 ssid my_net \
		   wepmode on wepkey 0x1234567890 weptxkey 1 up

SEE ALSO
     arp(4), netintro(4), usb(4), wlan(4), ifconfig(8)

HISTORY
     The upgt driver first appeared in OpenBSD 4.3.

AUTHORS
     The upgt driver was written by Marcus Glocker <mglocker@openbsd.org>.

     The hardware specification	was reverse engineered by the people at
     http://www.prism54.org.

CAVEATS
     The upgt driver just supports the USB 2.0 devices (GW3887 chipset)	but
     not the USB 1.0 devices containing	the NET2280, ISL3880, and ISL3886
     chipsets.	Some further efforts would be necessary	to add USB 1.0 support
     to	the driver.

FreeBSD	10.1			April 17, 2008			  FreeBSD 10.1

NAME | SYNOPSIS | DESCRIPTION | FILES | HARDWARE | EXAMPLES | SEE ALSO | HISTORY | AUTHORS | CAVEATS

Want to link to this manual page? Use this URL:
<http://www.freebsd.org/cgi/man.cgi?query=upgt&sektion=4&manpath=FreeBSD+10.0-RELEASE>

home | help