Skip site navigation (1)Skip section navigation (2)

FreeBSD Man Pages

Man Page or Keyword Search:
Man Architecture
Apropos Keyword Search (all sections) Output format
home | help
TRACEROUTE6(8)		FreeBSD	System Manager's Manual		TRACEROUTE6(8)

NAME
     traceroute6 -- print the route IPv6 packets will take to a	network	node

SYNOPSIS
     traceroute6 [-adIlnNrvU] [-f firsthop] [-g	gateway] [-m hoplimit]
		 [-p port] [-q probes] [-s src]	[-w waittime] [-A as_server]
		 target	[datalen]

DESCRIPTION
     The traceroute6 utility uses the IPv6 protocol hop	limit field to elicit
     an	ICMPv6 TIME_EXCEEDED response from each	gateway	along the path to some
     host.

     The only mandatory	parameter is the destination host name or IPv6
     address.  The default probe datagram carries 12 bytes of payload, in
     addition to the IPv6 header.  The size of the payload can be specified by
     giving a length (in bytes)	after the destination host name.

     Other options are:

     -a	     Turn on AS# lookups for each hop encountered.

     -A	as_server
	     Turn on AS# lookups and use the given server instead of the
	     default.

     -d	     Debug mode.

     -f	firsthop
	     Specify how many hops to skip in trace.

     -g	gateway
	     Specify intermediate gateway (traceroute6 uses routing header).

     -I	     Use ICMP6 ECHO instead of UDP datagrams.

     -l	     Print both	host hostnames and numeric addresses.  Normally
	     traceroute6 prints	only hostnames if -n is	not specified, and
	     only numeric addresses if -n is specified.

     -m	hoplimit
	     Specify maximum hoplimit, up to 255.  The default is 30 hops.

     -n	     Do	not resolve numeric address to hostname.

     -N	     Use a packet with no upper	layer header for the probes, instead
	     of	UDP datagrams.

     -p	port
	     Set UDP port number to port.

     -q	probes
	     Set the number of probe per hop count to probes.

     -r	     Bypass the	normal routing tables and send directly	to a host on
	     an	attached network.  If the host is not on a directly-connected
	     network, an error is returned.  This option corresponds to	the
	     SO_DONTROUTE socket option; it can	be used	to ping	a local	host
	     through an	interface that has no route through it (e.g., after
	     the interface was dropped by a routing daemon).

     -s	src  Src specifies the source IPv6 address to be used.

     -U	     Use UDP datagrams for the probes.	This is	the default.

     -v	     Be	verbose.

     -w	waittime
	     Specify the delay time between probes.

     This program prints the route to the given	destination and	the round-trip
     time to each gateway, in the same manner as traceroute.

     Here is a list of possible	annotations after the round-trip time for each
     gateway:

	   !N	   Destination Unreachable - No	Route to Host.

	   !P	   Destination Unreachable - Administratively Prohibited.

	   !S	   Destination Unreachable - Not a Neighbour.

	   !A	   Destination Unreachable - Address Unreachable.

	   !	   This	is printed if the hop limit is <= 1 on a port unreach-
		   able	message.  This means that the packet got to the	desti-
		   nation, but that the	reply had a hop	limit that was just
		   large enough	to allow it to get back	to the source of the
		   traceroute6.	 This was more interesting in the IPv4 case,
		   where some IP stack bugs could be identified	by this	behav-
		   iour.

EXIT STATUS
     The traceroute6 utility will exit with 0 on success, and non-zero on
     errors.

SEE ALSO
     ping(8), ping6(8),	traceroute(8)

HISTORY
     The traceroute6 utility first appeared in WIDE hydrangea IPv6 protocol
     stack kit.

FreeBSD	9.2			August 24, 2009			   FreeBSD 9.2

NAME | SYNOPSIS | DESCRIPTION | EXIT STATUS | SEE ALSO | HISTORY

Want to link to this manual page? Use this URL:
<http://www.freebsd.org/cgi/man.cgi?query=traceroute6&sektion=8&manpath=FreeBSD+9.3-RELEASE>

home | help