Skip site navigation (1)Skip section navigation (2)

FreeBSD Man Pages

Man Page or Keyword Search:
Man Architecture
Apropos Keyword Search (all sections) Output format
home | help
TL(4)		       FreeBSD Kernel Interfaces Manual			 TL(4)

NAME
     tl	-- Texas Instruments ThunderLAN	Ethernet device	driver

SYNOPSIS
     To	compile	this driver into the kernel, place the following lines in your
     kernel configuration file:

	   device miibus
	   device tl

     Alternatively, to load the	driver as a module at boot time, place the
     following line in loader.conf(5):

	   if_tl_load="YES"

DESCRIPTION
     The tl driver provides support for	PCI Ethernet adapters based on the
     Texas Instruments ThunderLAN Ethernet controller chip.

     The ThunderLAN controller has a standard MII interface that supports up
     to	32 physical interface devices (PHYs).  It also has a built-in 10baseT
     PHY hardwired at MII address 31, which may	be used	in some	10Mbps-only
     hardware configurations.  In 100Mbps configurations, a National Semicon-
     ductor DP83840A or	other MII-compliant PHY	may be attached	to the Thun-
     derLAN's MII bus.	If a DP83840A or equivalent is available, the Thunder-
     LAN chip can operate at either 100Mbps or 10Mbps in either	half-duplex or
     full-duplex modes.	 The ThunderLAN's built-in PHY and the DP83840A	also
     support autonegotiation.

     The tl driver supports the	following media	types:

     autoselect		   Enable autoselection	of the media type and options.
			   Note	that this option is only available on those
			   PHYs	that support autonegotiation.  Also, the PHY
			   will	not advertise those modes that have been
			   explicitly disabled using the following media
			   options.

     10baseT/UTP	   Set 10Mbps operation

     100baseTX		   Set 100Mbps (Fast Ethernet) operation

     10base5/AUI	   Enable AUI/BNC interface (useful only with the
			   built-in PHY).

     The tl driver supports the	following media	options:

     full-duplex	   Force full duplex operation

     half-duplex	   Force half duplex operation.

     hw-loopback	   Enable hardware loopback mode.

     Note that the 100baseTX media type	is only	available if supported by the
     PHY.  For more information	on configuring this device, see	ifconfig(8).

HARDWARE
     The tl driver supports Texas Instruments ThunderLAN based Ethernet	and
     Fast Ethernet adapters including a	large number of	Compaq PCI Ethernet
     adapters.	Also supported are:

     +o	 Olicom	OC-2135/2138 10/100 TX UTP adapter
     +o	 Olicom	OC-2325/OC-2326	10/100 TX UTP adapter
     +o	 Racore	8148 10baseT/100baseTX/100baseFX adapter
     +o	 Racore	8165 10/100baseTX adapter

     The tl driver also	supports the built-in Ethernet adapters	of various
     Compaq Prosignia servers and Compaq Deskpro desktop machines including:

     +o	 Compaq	Netelligent 10
     +o	 Compaq	Netelligent 10 T PCI UTP/Coax
     +o	 Compaq	Netelligent 10/100
     +o	 Compaq	Netelligent 10/100 Dual-Port
     +o	 Compaq	Netelligent 10/100 Proliant
     +o	 Compaq	Netelligent 10/100 TX Embedded UTP
     +o	 Compaq	Netelligent 10/100 TX UTP
     +o	 Compaq	NetFlex	3P
     +o	 Compaq	NetFlex	3P Integrated
     +o	 Compaq	NetFlex	3P w/BNC

DIAGNOSTICS
     tl%d: couldn't map	memory	A fatal	initialization error has occurred.

     tl%d: couldn't map	interrupt  A fatal initialization error	has occurred.

     tl%d: device timeout  The device has stopped responding to	the network,
     or	there is a problem with	the network connection (cable).

     tl%d: no memory for rx list  The driver failed to allocate	an mbuf	for
     the receiver ring.

     tl%d: no memory for tx list  The driver failed to allocate	an mbuf	for
     the transmitter ring when allocating a pad	buffer or collapsing an	mbuf
     chain into	a cluster.

SEE ALSO
     arp(4), miibus(4),	netintro(4), ng_ether(4), ifconfig(8)

HISTORY
     The tl device driver first	appeared in FreeBSD 2.2.

AUTHORS
     The tl driver was written by Bill Paul <wpaul@ctr.columbia.edu>.

FreeBSD	10.1			 July 16, 2005			  FreeBSD 10.1

NAME | SYNOPSIS | DESCRIPTION | HARDWARE | DIAGNOSTICS | SEE ALSO | HISTORY | AUTHORS

Want to link to this manual page? Use this URL:
<https://www.freebsd.org/cgi/man.cgi?query=tl&sektion=4&manpath=FreeBSD+8.1-RELEASE>

home | help