Skip site navigation (1)Skip section navigation (2)

FreeBSD Man Pages

Man Page or Keyword Search:
Man Architecture
Apropos Keyword Search (all sections) Output format
home | help
SK(4)		       FreeBSD Kernel Interfaces Manual			 SK(4)

NAME
     sk	-- SysKonnect SK-984x and SK-982x PCI Gigabit Ethernet adapter driver

SYNOPSIS
     To	compile	this driver into the kernel, place the following lines in your
     kernel configuration file:

	   device miibus
	   device sk

     Alternatively, to load the	driver as a module at boot time, place the
     following line in loader.conf(5):

	   if_sk_load="YES"

DESCRIPTION
     The sk driver provides support for	the SysKonnect SK-984x and SK-982x
     series PCI	Gigabit	Ethernet adapters.

     The SysKonnect adapters consist of	two main components: the XaQti Corp.
     XMAC II gigabit MAC and the SysKonnect GEnesis controller ASIC.  The XMAC
     provides the gigabit MAC and PHY support while the	GEnesis	provides an
     interface to the PCI bus, DMA support, packet buffering and arbitration.
     The GEnesis can control up	to two XMACs simultaneously, allowing dual-
     port NIC configurations.

     The SK-982x 1000baseT adapters also include a Broadcom BCM5400 1000baseTX
     PHY which is used in place	of the XMAC's internal PHY.  The Broadcom PHY
     is	connected to the XMAC via its GMII port.

     The sk driver configures dual port	SysKonnect adapters such that each
     XMAC is treated as	a separate logical network interface.  Both ports can
     operate independently of each other and can be connected to separate net-
     works.  The SysKonnect driver software currently only uses	the second
     port on dual port adapters	for failover purposes: if the link on the pri-
     mary port fails, the SysKonnect driver will automatically switch traffic
     onto the second port.

     Also supported is the Marvell Semiconductor 88E100* gigabit PHY.

     The XaQti XMAC II supports	full and half duplex operation with autonego-
     tiation.  The XMAC	also supports unlimited	frame sizes.  Support for
     jumbo frames is provided via the interface	MTU setting.  Selecting	an MTU
     larger than 1500 bytes with the ifconfig(8) utility configures the
     adapter to	receive	and transmit jumbo frames.  Using jumbo	frames can
     greatly improve performance for certain tasks, such as file transfers and
     data streaming.

     The sk driver supports the	following media	types:

     autoselect		   Enable autoselection	of the media type and options.
			   The user can	manually override the autoselected
			   mode	by adding media	options	to the /etc/rc.conf
			   file.

     1000baseTX		   Set 1000baseTX operation over twisted pair.	This
			   is only available for SK-982x series	adapters with
			   1000baseT ports.  Both full-duplex and half-duplex
			   modes are supported.

     1000baseSX		   Set 1000Mbps	(Gigabit Ethernet) operation.  Both
			   full-duplex and half-duplex modes are supported.

     The sk driver supports the	following media	options:

     full-duplex	   Force full duplex operation

     half-duplex	   Force half duplex operation.

     For more information on configuring this device, see ifconfig(8).

HARDWARE
     Adapters supported	by the sk driver include:

     +o	 3Com 3C940 single port, 1000baseT adapter
     +o	 3Com 3C2000-T single port, 1000baseT adapter
     +o	 Belkin	F5D5005	single port, 1000baseT adapter
     +o	 D-Link	DGE-530T single	port, 1000baseT	adapter
     +o	 Linksys (revision 2) single port, 1000baseT adapter
     +o	 SK-9521 SK-NET	GE-T single port, 1000baseT adapter
     +o	 SK-9821 SK-NET	GE-T single port, 1000baseT adapter
     +o	 SK-9822 SK-NET	GE-T dual port,	1000baseT adapter
     +o	 SK-9841 SK-NET	GE-LX single port, single mode fiber adapter
     +o	 SK-9842 SK-NET	GE-LX dual port, single	mode fiber adapter
     +o	 SK-9843 SK-NET	GE-SX single port, multimode fiber adapter
     +o	 SK-9844 SK-NET	GE-SX dual port, multimode fiber adapter
     +o	 SMC 9452TX single port, 1000baseT adapter

LOADER TUNABLES
     Tunables can be set at the	loader(8) prompt before	booting	the kernel or
     stored in loader.conf(5).

     hw.skc.jumbo_disable
	     Disable jumbo frame support.  Systems with	less memory can	set it
	     to	a non-zero value to save memory.  The default value is 0.

SYSCTL VARIABLES
     The following variable is available as both sysctl(8) variable and
     loader(8) tunable:

     dev.skc.%d.int_mod
	     This variable controls interrupt moderation.  The accepted	range
	     is	10 to 10000.  The default value	is 100 microseconds.  The
	     interface has to be brought down and up again before a change
	     takes effect.

DIAGNOSTICS
     sk%d: couldn't map	memory	A fatal	initialization error has occurred.

     sk%d: couldn't map	ports  A fatal initialization error has	occurred.

     sk%d: couldn't map	interrupt  A fatal initialization error	has occurred.

     sk%d: no memory for softc struct!	The driver failed to allocate memory
     for per-device instance information during	initialization.

     sk%d: failed to enable memory mapping!  The driver	failed to initialize
     PCI shared	memory mapping.	 This might happen if the card is not in a
     bus-master	slot.

     sk%d: no memory for jumbo buffers!	 The driver failed to allocate memory
     for jumbo frames during initialization.

     sk%d: watchdog timeout  The device	has stopped responding to the network,
     or	there is a problem with	the network connection (cable).

SEE ALSO
     altq(4), arp(4), miibus(4), netintro(4), ng_ether(4), vlan(4),
     ifconfig(8)

     XaQti XMAC	II datasheet, http://www.xaqti.com.

     SysKonnect	GEnesis	programming manual, http://www.syskonnect.com.

HISTORY
     The sk device driver first	appeared in FreeBSD 3.0.

AUTHORS
     The sk driver was written by Bill Paul <wpaul@ctr.columbia.edu>.

FreeBSD	10.1		       November	23, 2010		  FreeBSD 10.1

NAME | SYNOPSIS | DESCRIPTION | HARDWARE | LOADER TUNABLES | SYSCTL VARIABLES | DIAGNOSTICS | SEE ALSO | HISTORY | AUTHORS

Want to link to this manual page? Use this URL:
<http://www.freebsd.org/cgi/man.cgi?query=sk&sektion=4&manpath=FreeBSD+9.0-RELEASE>

home | help