Skip site navigation (1)Skip section navigation (2)

FreeBSD Man Pages

Man Page or Keyword Search:
Man Architecture
Apropos Keyword Search (all sections) Output format
home | help
POLLING(4)             FreeBSD Kernel Interfaces Manual             POLLING(4)

NAME
     polling -- device polling support

SYNOPSIS
     options DEVICE_POLLING

DESCRIPTION
     Device polling (polling for brevity) refers to a technique that lets the
     operating system periodically poll devices, instead of relying on the
     devices to generate interrupts when they need attention.  This might seem
     inefficient and counterintuitive, but when done properly, polling gives
     more control to the operating system on when and how to handle devices,
     with a number of advantages in terms of system responsiveness and perfor-
     mance.

     In particular, polling reduces the overhead for context switches which is
     incurred when servicing interrupts, and gives more control on the sched-
     uling of the CPU between various tasks (user processes, software inter-
     rupts, device handling) which ultimately reduces the chances of livelock
     in the system.

   Principles of Operation
     In the normal, interrupt-based mode, devices generate an interrupt when-
     ever they need attention.  This in turn causes a context switch and the
     execution of an interrupt handler which performs whatever processing is
     needed by the device.  The duration of the interrupt handler is poten-
     tially unbounded unless the device driver has been programmed with real-
     time concerns in mind (which is generally not the case for FreeBSD driv-
     ers).  Furthermore, under heavy traffic load, the system might be persis-
     tently processing interrupts without being able to complete other work,
     either in the kernel or in userland.

     Device polling disables interrupts by polling devices at appropriate
     times, i.e., on clock interrupts and within the idle loop.  This way, the
     context switch overhead is removed.  Furthermore, the operating system
     can control accurately how much work to spend in handling device events,
     and thus prevent livelock by reserving some amount of CPU to other tasks.

     Enabling polling also changes the way software network interrupts are
     scheduled, so there is never the risk of livelock because packets are not
     processed to completion.

   Enabling polling
     Currently only network interface drivers support the polling feature.  It
     is turned on and off with help of ifconfig(8) command.

   MIB Variables
     The operation of polling is controlled by the following sysctl(8) MIB
     variables:

     kern.polling.user_frac
             When polling is enabled, and provided that there is some work to
             do, up to this percent of the CPU cycles is reserved to userland
             tasks, the remaining fraction being available for polling pro-
             cessing.  Default is 50.

     kern.polling.burst
             Maximum number of packets grabbed from each network interface in
             each timer tick.  This number is dynamically adjusted by the ker-
             nel, according to the programmed user_frac, burst_max, CPU speed,
             and system load.

     kern.polling.each_burst
             The burst above is split into smaller chunks of this number of
             packets, going round-robin among all interfaces registered for
             polling.  This prevents the case that a large burst from a single
             interface can saturate the IP interrupt queue
             (net.inet.ip.intr_queue_maxlen).  Default is 5.

     kern.polling.burst_max
             Upper bound for kern.polling.burst.  Note that when polling is
             enabled, each interface can receive at most (HZ * burst_max)
             packets per second unless there are spare CPU cycles available
             for polling in the idle loop.  This number should be tuned to
             match the expected load (which can be quite high with GigE
             cards).  Default is 150 which is adequate for 100Mbit network and
             HZ=1000.

     kern.polling.idle_poll
             Controls if polling is enabled in the idle loop.  There are no
             reasons (other than power saving or bugs in the scheduler's han-
             dling of idle priority kernel threads) to disable this.

     kern.polling.reg_frac
             Controls how often (every reg_frac / HZ seconds) the status reg-
             isters of the device are checked for error conditions and the
             like.  Increasing this value reduces the load on the bus, but
             also delays the error detection.  Default is 20.

     kern.polling.handlers
             How many active devices have registered for polling.

     kern.polling.enable
             Legacy MIB, that was used to enable or disable polling globally.
             Currently if set to 1, polling is enabled on all capable inter-
             faces.  If set to 0, polling is disabled on all interfaces.

     kern.polling.short_ticks
     kern.polling.lost_polls
     kern.polling.pending_polls
     kern.polling.residual_burst
     kern.polling.phase
     kern.polling.suspect
     kern.polling.stalled
             Debugging variables.

SUPPORTED DEVICES
     Device polling requires explicit modifications to the device drivers.  As
     of this writing, the bge(4), dc(4), em(4), fwe(4), fwip(4), fxp(4),
     ixgb(4), nge(4), re(4), rl(4), sf(4), sis(4), ste(4), stge(4), vge(4),
     vr(4), and xl(4) devices are supported, with others in the works.  The
     modifications are rather straightforward, consisting in the extraction of
     the inner part of the interrupt service routine and writing a callback
     function, *_poll(), which is invoked to probe the device for events and
     process them.  (See the conditionally compiled sections of the devices
     mentioned above for more details.)

     As in the worst case the devices are only polled on clock interrupts, in
     order to reduce the latency in processing packets, it is not advisable to
     decrease the frequency of the clock below 1000 Hz.

HISTORY
     Device polling first appeared in FreeBSD 4.6 and FreeBSD 5.0.

AUTHORS
     Device polling was written by Luigi Rizzo <luigi@iet.unipi.it>.

FreeBSD 6.2                    December 2, 2006                    FreeBSD 6.2

NAME | SYNOPSIS | DESCRIPTION | SUPPORTED DEVICES | HISTORY | AUTHORS

Want to link to this manual page? Use this URL:
<https://www.freebsd.org/cgi/man.cgi?query=polling&sektion=4&manpath=FreeBSD+6.2-RELEASE>

home | help