Skip site navigation (1)Skip section navigation (2)

FreeBSD Man Pages

Man Page or Keyword Search:
Man Architecture
Apropos Keyword Search (all sections) Output format
home | help
MXGE(4)		       FreeBSD Kernel Interfaces Manual		       MXGE(4)

NAME
     mxge -- Myricom Myri10GE 10 Gigabit Ethernet adapter driver

SYNOPSIS
     To	compile	this driver into the kernel, place the following lines in your
     kernel configuration file:

	   device firmware
	   device mxge

     Alternatively, to load the	driver as a module at boot time, place the
     following lines in	loader.conf(5):

	   if_mxge_load="YES"
	   mxge_ethp_z8e_load="YES"
	   mxge_eth_z8e_load="YES"

DESCRIPTION
     The mxge driver provides support for PCI Express 10 Gigabit Ethernet
     adapters based on the Myricom LANai Z8E chip.  The	driver supports	Trans-
     mit/Receive checksum offload, Jumbo Frames	as well	as TCP segmentation
     offload (TSO).  For further hardware information, see
     http://www.myri.com/.

     For questions related to hardware requirements, refer to the documenta-
     tion supplied with	your Myri10GE adapter.	All hardware requirements
     listed apply to use with FreeBSD.

     Support for Jumbo Frames is provided via the interface MTU	setting.
     Selecting an MTU larger than 1500 bytes with the ifconfig(8) utility con-
     figures the adapter to receive and	transmit Jumbo Frames.	The maximum
     MTU size for Jumbo	Frames is 9000.

     For more information on configuring this device, see ifconfig(8).

HARDWARE
     The mxge driver supports 10 Gigabit Ethernet adapters based on the	Myri-
     com LANai Z8E chips:

     +o	 Myricom 10GBase-CX4 (10G-PCIE-8A-C, 10G-PCIE-8AL-C)
     +o	 Myricom 10GBase-R (10G-PCIE-8A-R, 10G-PCIE-8AL-R)
     +o	 Myricom 10G XAUI over ribbon fiber (10G-PCIE-8A-Q, 10G-PCIE-8AL-Q)

LOADER TUNABLES
     Tunables can be set at the	loader(8) prompt before	booting	the kernel or
     stored in loader.conf(5).

     hw.mxge.flow_control_enabled
	     Whether or	not hardware flow control is enabled on	the adapter.
	     The default value is 1.

     hw.mxge.intr_coal_delay
	     This value	delays the generation of all interrupts	in units of 1
	     microsecond.  The default value is	30.

     hw.mxge.skip_pio_read
	     This value	determines whether or not the driver may omit doing a
	     pio read in the interrupt handler which ensures that the inter-
	     rupt line has been	deasserted when	using xPIC interrupts.	A non-
	     zero value	may result in lower CPU	overhead, however it may also
	     result in spurious	interrupts.  The default value is 0.

DIAGNOSTICS
     mxge%d: Unable to allocate	bus resource: memory  A	fatal initialization
     error has occurred.

     mxge%d: Unable to allocate	bus resource: interrupt	 A fatal initializa-
     tion error	has occurred.

     mxge%d: Could not find firmware image %s  The appropriate firmware	kld
     module was	not installed.	This is	a fatal	initialization error.

SUPPORT
     For general information and support, go to	the Myricom support website
     at: http://www.myri.com/scs/.

     If	an issue is identified with the	released source	code on	the supported
     kernel with a supported adapter, email the	specific information related
     to	the issue to <help@myri.com>.

SEE ALSO
     altq(4), arp(4), netintro(4), ng_ether(4),	ifconfig(8)

HISTORY
     The mxge device driver first appeared in FreeBSD 6.3.

AUTHORS
     The mxge driver was written by Andrew Gallatin <gallatin@FreeBSD.org>.

FreeBSD	9.2		      September	15, 2006		   FreeBSD 9.2

NAME | SYNOPSIS | DESCRIPTION | HARDWARE | LOADER TUNABLES | DIAGNOSTICS | SUPPORT | SEE ALSO | HISTORY | AUTHORS

Want to link to this manual page? Use this URL:
<http://www.freebsd.org/cgi/man.cgi?query=mxge&sektion=4&manpath=FreeBSD+7.0-RELEASE>

home | help