Skip site navigation (1)Skip section navigation (2)

FreeBSD Man Pages

Man Page or Keyword Search:
Man Architecture
Apropos Keyword Search (all sections) Output format
home | help
FDFORMAT(1)             FreeBSD General Commands Manual            FDFORMAT(1)

NAME
     fdformat -- format floppy disks

SYNOPSIS
     fdformat [-F fill] [-f fmt] [-s fmtstr] [-nqvy] device

DESCRIPTION
     The fdformat utility formats a floppy disk at device, where device may
     either be given as a full path name of a device node for a floppy disk
     drive (e.g. /dev/fd0), or using an abbreviated name that will be looked
     up under /dev (e.g. ``fd0'').

     The options are as follows:

     -F fill    Use fill as the fill byte for newly formatted sectors.  fill
                must be a number in the range 0 through 255 using common C
                language notation.  The default value is ``0xf6''.

     -f fmt     Specify the density settings for a fmt kilobyte format, as
                described in fdcontrol(8).

     -s fmtstr  Specify the density settings using explicit parameters, as
                described in fdcontrol(8).

     -n         Do not verify floppy after formatting.

     -q         Suppress any normal output from the command, and do not ask
                the user for a confirmation whether to format the floppy disk
                at device.

     -v         Do not format, verify only.

     -y         Do not ask for confirmation whether to format the floppy disk
                but still report formatting status.

     For non-autoselecting subdevices, neither -f fmt nor -s fmtstr may be
     specified, since the preconfigured media density settings from the kernel
     driver will always be used.  However, if device is a device with auto-
     matic media density selection (see fdc(4)), both methods can be used to
     override the density settings for the newly formatted medium (without
     permanently changing the density settings of device).

     If the -q flag has not been specified, the user is asked for a confirma-
     tion of the intended formatting process.  In order to continue, an answer
     of `y' must be given.

     Note that fdformat does only perform low-level formatting.  In order to
     create a file system on the medium, see the commands newfs(8) for a UFS
     file system, or newfs_msdos(8) for an MS-DOS (FAT) file system.

EXIT STATUS
     An exit status of 0 is returned upon successful operation.  Exit status 1
     is returned on any errors during floppy formatting, and an exit status of
     2 reflects invalid arguments given to the program (along with an appro-
     priate information written to diagnostic output).

DIAGNOSTICS
     Unless -q has been specified, a single letter is printed to standard out-
     put to inform the user about the progress of work.  First, an `F' is
     printed when the track is being formatted, then a `V' while it is being
     verified, and if an error has been detected, it will finally change to
     `E'.  Detailed status information (cylinder, head and sector number, and
     the exact cause of the error) will be printed for up to 10 errors after
     the entire formatting process has completed.

SEE ALSO
     fdc(4), fdcontrol(8), newfs(8), newfs_msdos(8)

HISTORY
     The fdformat utility has been developed for 386BSD 0.1 and upgraded to
     the new fdc(4) floppy disk driver.  It later became part of the
     FreeBSD 1.1 system.  Starting with FreeBSD 5.0, it uses the unified den-
     sity specifications as described in fdcontrol(8).

AUTHORS
     The program has been contributed by Jorg Wunsch, Dresden, with changes by
     Serge Vakulenko and Andrey A. Chernov, Moscow.

FreeBSD 6.2                    December 25, 2001                   FreeBSD 6.2

NAME | SYNOPSIS | DESCRIPTION | EXIT STATUS | DIAGNOSTICS | SEE ALSO | HISTORY | AUTHORS

Want to link to this manual page? Use this URL:
<http://www.freebsd.org/cgi/man.cgi?query=fdformat&sektion=1&manpath=FreeBSD+6.2-RELEASE>

home | help