Skip site navigation (1)Skip section navigation (2)

FreeBSD Man Pages

Man Page or Keyword Search:
Man Architecture
Apropos Keyword Search (all sections) Output format
home | help
CISS(4)		       FreeBSD Kernel Interfaces Manual		       CISS(4)

NAME
     ciss -- Common Interface for SCSI-3 Support driver

SYNOPSIS
     To	compile	this driver into the kernel, place the following lines in your
     kernel configuration file:

	   device scbus
	   device ciss

     Alternatively, to load the	driver as a module at boot time, place the
     following line in loader.conf(5):

	   ciss_load="YES"

DESCRIPTION
     The ciss driver claims to provide a common	interface between generic SCSI
     transports	and intelligent	host adapters.

     The ciss driver supports CISS as defined in the document entitled CISS
     Command Interface for SCSI-3 Support Open Specification, Version 1.04,
     Valence Number 1, dated 2000/11/27, produced by Compaq Computer Corpora-
     tion.

     We	provide	a shim layer between the ciss interface	and CAM(4), offloading
     most of the queueing and being-a-disk chores onto CAM.  Entry to the
     driver is via the PCI bus attachment ciss_probe(),	ciss_attach(), etc.
     and via the CAM interface ciss_cam_action(), and ciss_cam_poll().	The
     Compaq ciss adapters require faked	responses to get reasonable behavior
     out of them.  In addition,	the ciss command set is	by no means adequate
     to	support	the functionality of a RAID controller,	and thus the supported
     Compaq adapters utilize portions of the control protocol from earlier
     Compaq adapter families.

     Currently ciss only supports the ``simple'' transport layer over PCI.
     This interface (ab)uses the I2O register set (specifically	the post
     queues) to	exchange commands with the adapter.  Other interfaces are
     available,	but we are not supposed	to know	about them, and	it is dubious
     whether they would	provide	major performance improvements except under
     extreme load.

     Non-disk devices (such as internal	DATs and devices attached to the
     external SCSI bus)	are supported as normal	CAM devices provided that they
     are exported by the controller firmware and are not marked	as being
     masked.  Masked devices can be exposed by setting the
     hw.ciss.expose_hidden_physical tunable to non-zero	at boot	time.  Direct
     Access devices (such as disk drives) are only exposed as pass(4) devices.
     Hot-insertion and removal of devices is supported but a bus rescan	might
     be	necessary.

     The problem which adapter freezes with the	message	``ADAPTER HEARTBEAT
     FAILED'' might be solved by updating the firmware and/or setting the
     hw.ciss.nop_message_heartbeat tunable to non-zero at boot time.

HARDWARE
     Controllers supported by the ciss driver include:

     +o	 Compaq	Smart Array 5300
     +o	 Compaq	Smart Array 532
     +o	 Compaq	Smart Array 5i
     +o	 HP Smart Array	5312
     +o	 HP Smart Array	6i
     +o	 HP Smart Array	641
     +o	 HP Smart Array	642
     +o	 HP Smart Array	6400
     +o	 HP Smart Array	6400 EM
     +o	 HP Smart Array	E200
     +o	 HP Smart Array	E200i
     +o	 HP Smart Array	P400
     +o	 HP Smart Array	P400i
     +o	 HP Smart Array	P600
     +o	 HP Smart Array	P800
     +o	 HP Modular Smart Array	20 (MSA20)
     +o	 HP Modular Smart Array	500 (MSA500)

SEE ALSO
     cam(4), pass(4), xpt(4), loader.conf(5), camcontrol(8)

     CISS Command Interface for	SCSI-3 Support Open Specification, Version
     1.04, Valence Number 1, Compaq Computer Corporation, 2000/11/27.

AUTHORS
     The ciss driver was written by Mike Smith <msmith@FreeBSD.org>.

     This manual page is based on his comments and was written by Tom Rhodes
     <trhodes@FreeBSD.org>.

FreeBSD	9.3		       November	3, 2005			   FreeBSD 9.3

NAME | SYNOPSIS | DESCRIPTION | HARDWARE | SEE ALSO | AUTHORS

Want to link to this manual page? Use this URL:
<http://www.freebsd.org/cgi/man.cgi?query=ciss&sektion=4&manpath=FreeBSD+7.0-RELEASE>

home | help